CONDENSER, REMOVING AND INSTALLING, Vehicles with 2.0L, 3.0L and 3.2L: Removing

WARNING: This page does not describe the selected car, but rather 13 other vehicles, including the 2017 Audi SQ5, 2017 Audi Q5, 2016 Audi SQ5, 2016 Audi Q5, and 2015 Audi SQ5. However, it is still accessible from the selected car via links, so may be relevant.

-- Turn off the ignition.

-- Discharge the refrigerant circuit. Refer to USING SERVICE STATION . For additional information, refer to OVERVIEW - REFRIGERANT CIRCUIT, NOT OPENING THE REFRIGERANT CIRCUIT, VEHICLES WITHOUT HIGH VOLTAGE SYSTEM and OVERVIEW - REFRIGERANT CIRCUIT, OPENING THE REFRIGERANT CIRCUIT, VEHICLES WITHOUT HIGH VOLTAGE SYSTEM (Refrigerant R134a, Servicing; Refrigerant Circuit, Using Service Station).

NOTE:

Depending on the allocation of the service connection to the refrigerant line and vehicle version, it may be necessary to remove the left additional reinforcement on the tower brace so that the service coupling of the A/C service station can be connected (for example, on the Audi Q5). Refer to OVERVIEW - SUSPENSION STRUT WITH MOUNTING BRACKET, SHOCK ABSORBER FORK, UPPER CONTROL ARM AND TOWER BRACE and USING SERVICE STATION . For additional information, refer to OVERVIEW - REFRIGERANT CIRCUIT, NOT OPENING THE REFRIGERANT CIRCUIT, VEHICLES WITHOUT HIGH VOLTAGE SYSTEM and OVERVIEW - REFRIGERANT CIRCUIT, OPENING THE REFRIGERANT CIRCUIT, VEHICLES WITHOUT HIGH VOLTAGE SYSTEM (Refrigerant R134a, Servicing; Refrigerant Circuit, Using A/C Service Station).

-- Remove the refrigerant lines from the condenser. Refer to REFRIGERANT LINES, DISCONNECTING AND CONNECTING AT CONDENSER .

-- Remove the bolts (or clips) -1, 2, 3 and 5-. Refer to LOCK CARRIER COVER, REMOVING AND INSTALLING .

Fig 1: Front Lock Carrier Cover

Courtesy of AUDI OF AMERICA, LLC

-- Lift the cover -4- on the lock carrier and disengage it on the radiator grille. Refer to LOCK CARRIER COVER, REMOVING AND INSTALLING .

-- Remove the bolts -arrows-.

Fig 2: Identifying Air Duct Components

Courtesy of AUDI OF AMERICA, LLC

-- Remove the air guide -1- on the intermediate flange -2- for the air filter housing.

-- Disconnect the connector -C- from the A/C Pressure/Temperature Sensor -G395-.

Fig 3: Disconnect Electrical Connector On A/C Pressure/Temperature Sensor

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the connector -B- to the front parking aid sensors and the connector to the Outside Air Temperature Sensor -G17- -A-.

NOTE:

Different installation locations of the Outside Air Temperature Sensor -G17- (this illustration shows the location for vehicles of MY 2008). Refer to Outside Air Temperature Sensor -G17-, REMOVING AND INSTALLING .

-- Remove the front bumper cover end plate (depending on the vehicle version, for example, for the Audi Q5 it is currently not always necessary). Refer to Front Bumper .

NOTE:

On vehicles with a grille -A- (only specific vehicles with safety feature against rocks and stone chips) the front bumper cover and grille -A- must be removed in order to move and remove the air duct -B-.

Fig 4: View Of Grille And Air Ducts

Courtesy of AUDI OF AMERICA, LLC

-- Unlock the retaining straps -arrows A- (each two straps, one on top and one below on the air guide) and move the left and right air guide -1- toward the center of the vehicle -arrow B-.

Fig 5: Locating Left & Right Air Duct Tabs

Courtesy of AUDI OF AMERICA, LLC

Vehicles with a power steering oil cooler:

Fig 6: If Applicable, Release Clamps And Tilt Power Steering Coolant Hose

Courtesy of AUDI OF AMERICA, LLC

-- Unlock the retaining clamps -arrow A- and move the power steering cooling coil -1- forward -arrow B-.

-- Remove the power steering oil cooler cooling coil from the condenser and lay it on the engine.

NOTE:

In the illustration the installation position is shown with the bumper cover removed.

All:

Fig 7: Removing A/C Condenser

Courtesy of AUDI OF AMERICA, LLC

-- Unlock the retaining clamps -1- in -arrow direction A- and remove the condenser -2- upward and out of the brackets on the radiator -arrows B-.

NOTE:

In the illustration, with the bumper cover removed.