Oxygen Sensor 1 After Catalytic Converter -GX7-, CHECKING
WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2016 Audi A4 Quattro, 2016 Audi A4, 2015 Audi A4 Quattro, 2014 Audi A4 Quattro, and 2013 Audi A4. However, it is still accessible from the selected car via links, so may be relevant.
General Description
The Oxygen Sensor 1 After Catalytic Converter -GX7- downstream of the primary catalytic converter supplies the Engine Control Module -J623- with a voltage signal (nonlinear) indicating "rich" or "lean. If the primary catalytic converter is supersaturated with oxygen (lean mixture), Oxygen Sensor 1 After Catalytic Converter -GX7- will send the Engine Control Module -J623- a nonlinear signal indicating the lean mixture condition. The mixture is then enriched with fuel until the oxygen has been "displaced" from the catalytic converter. This condition, in turn, is registered by Oxygen Sensor 1 After Catalytic Converter -GX7- as a nonlinear signal indicating the rich mixture condition. The mixture is then leaned out by the Engine Control Module -J623-. If the nonlinear signal is received again, the mixture will again be enriched. The frequency, or period, during which the mixture is enriched or leaned out is variable, being dependent on the gas flow rate (engine load) at that moment.
Note the Oxygen Sensor 1 After Catalytic Converter -GX7- is also referred to as the Oxygen Sensor After Three Way Catalytic Converter -G130-.
The Oxygen Sensor 1 After Catalytic Converter -GX7- contains the following components:
- Oxygen Sensor After Three Way Catalytic Converter -G130-
- Heater For Oxygen Sensor 1 After Catalytic Converter -Z29-
The Oxygen Sensor 1 After Catalytic Converter -GX7- components cannot be serviced separately, it must be serviced as a unit.
Special tools and workshop equipment required
- Multimeter
- Wiring Diagram
- Scan Tool
Test requirements
- Fuses OK.
- Battery voltage OK.
- Switch OFF all electrical and electronic accessories.
- Vehicles with Auto. Transmission, ensure Selector Lever position is in "P".
- Vehicles with Man. Transmission, ensure Shifter Lever position is in "N" with Parking Brake applied.
- Coolant Temperature: ≥ 80° C.
- Observe all safety precautions: SAFETY PRECAUTIONS
.
- View clean working conditions: CLEAN WORKING CONDITIONS
.
- For Hybrid vehicles refer to: HIGH VOLTAGE SYSTEM GENERAL WARNINGS
.
Test Procedure
| Step |
Procedure |
Result / Action to Take |
| 1 |
- PERFORM: Preliminary Check to verify the customers complaint. Refer to Oxygen Sensor Preliminary Tests in PRELIMINARY CHECK
.
-- Was Complaint verified? |
-- YES:
-- NO:
- GATHER more information from customer about the complaint.
|
| 2 |
- IGNITION: OFF.
- DISCONNECT: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector.
- CHECK: Oxygen Sensor 1 After Catalytic Converter -GX7- component connector terminals 1 to 2 for resistance.
- SPECIFIED VALUE: 2 - 4 Ω (@ 25° C).
-- Was Value obtained? |
-- YES:
-- NO:
- REPLACE: Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to appropriate repair information.
- GO TO: Step 6
|
| 3 |
- IGNITION: ON.
- CHECK: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector terminal 1 to ground for voltage.
- IGNITION: OFF.
- SPECIFIED VALUE: Battery voltage.
-- Was Value obtained? |
-- YES:
-- NO:
- PERFORM: Visual Inspection of wiring and component.
- CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
- REPAIR: Faulty wiring or connector.
- GO TO: Step 6
|
| 4 |
- RECONNECT: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector.
- CONNECT: Scan Tool.
- START: Engine and let Idle.
- Perform the function test located in diagnostic mode 06. Refer to appropriate Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions, DIAGNOSTIC MODES 01 - 0A
.
- IGNITION: OFF.
- SPECIFIED VALUE: Mode 6 Pass.
-- Were Values obtained? |
-- YES:
- FAULT: Is intermittent.
- PERFORM: Visual Inspection of wiring and component.
- CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
- REPAIR: Faulty wiring or connector.
- GO TO: Step 6
-- NO:
|
| 5 |
- DISCONNECT: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector.
- REMOVE: Engine Control Module -J623-. Refer to appropriate repair information.
- CHECK: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector terminal 2 to the Engine Control Module -J623- harness connector T94 / 29 for resistance.
- CHECK: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector terminal 3 to the Engine Control Module -J623- harness connector T94 / 34 for resistance.
- CHECK: Oxygen Sensor 1 After Catalytic Converter -GX7- harness connector terminal 4 to the Engine Control Module -J623- harness connector T94 / 62 for resistance.
- SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω).
-- Were Values obtained? |
-- YES:
- REPLACE: Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to appropriate repair information.
- GO TO: Step 6
-- NO:
- PERFORM: Visual Inspection of wiring and component.
- CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
- REPAIR: Faulty wiring or connector.
- GO TO: Step 6
|
| 6 |
- Final Procedure
- Perform a road test to verify repair
-- Does the original DTC return? |
-- YES:
- CHECK: Engine Control Module -J623- harness connector for any damaged, pushed-out pins.
- REPAIR: As necessary.
- If all electrical connections are OK:
- REPLACE: Engine Control Module -J623-. Refer to appropriate repair information.
- Clear the DTC's. Refer to DIAGNOSTIC MODE 04 - ERASE DTC MEMORY
.
- Repair is complete. Generate Readiness Code. Refer to READINESS CODE
.
- Return vehicle to Customer.
-- NO:
- Perform the diagnostic procedure for any DTC's.
- If no DTC's return the repair is complete.
- Return vehicle to customer.
|