LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2016 >> S5 Prestige, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 504 (Steering (Sedan)) >> 48 Steering >> Steering Column >> Overview - Steering Column

Overview - Steering Column

WARNING: This page does not describe the selected car, but rather 18 other vehicles, including the 2016 Audi S4, 2016 Audi A4 Quattro, 2016 Audi A4, 2015 Audi S4, and 2015 Audi A4 Quattro. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Steering Column Overview
GWWA48-10503Courtesy of AUDI OF AMERICA, LLC
  1. Bolt
    • Tightening specification.
      • 20 Nm
      • Quantity: 4
  2. Mounting Bracket
  3. Central Tube
  4. Bolt
    • 5 Nm
  5. Electronic Steering Column Lock Control Module -J764-
    • Installed on vehicles with lock system
    • Removing and installing. Refer to Electronic Steering Column Lock Control Module -J764-, REMOVING AND INSTALLING .
    • If the Electronic Steering Column Lock Control Module -J764- was replaced, the following steps must be performed with the Vehicle Diagnostic Tester. To do so, select the appropriate program in "Guided Functions  " and follow the instructions on the screen.
  6. Steering Column
    • Depending on the version of the steering (with or without dynamic steering) different versions of the steering columns are installed .
    • Actuator -arrow- installed on vehicles with dynamic steering.
    • The actuator -arrow- must not be loosened or separated from the steering column.
    • The actuator and the steering column are one component; they are replaced together.
    • An "adjusting element for active steering (dynamic steering) safety lock" is installed on the actuator -arrow-.
    • Adjusting element for active steering (dynamic steering) safety lock. Refer to Active Steering Safety Lock Actuator -F437-, REMOVING AND INSTALLING .
    • If the steering column and adjuster were replaced, then it is necessary to perform a basic setting on the dynamic steering. Refer to DYNAMIC STEERING BASIC SETTING .
    • Removing and installing. Refer to STEERING COLUMN, REMOVING AND INSTALLING .
    • Check for damage. Refer to STEERING COLUMN, CHECKING FOR DAMAGE .
  7. Right Knee Bar
    • Installed depending on the market
  8. Bolt
    • 20 Nm
    • 22 Nm on the Cabriolet
    • Quantity: 2
    • Depending on the market, the knee bar is bolted on the right driver side
    • Follow the assembly sequence when installing. Refer to Figure.
  9. Bolt
    • Tightening specification
      • 20 Nm
  10. Bolt
    • 20 Nm
    • Quantity: 2
    • Follow the assembly sequence when installing. Refer to Figure.
  11. Bolt
    • 20 Nm
    • Quantity: 2
    • Follow the assembly sequence when installing. Refer to Figure.
  12. Handle
  13. Bolt
    • 3 Nm
  14. Bolt
    • 20 Nm
    • Quantity: 2
    • Follow the assembly sequence when installing. Refer to Figure.
  15. Bolt
    • 30 Nm +90°
    • Always replace if removed
    • The threaded hole for the bolt must always be cleaned (for example, using a thread tap).
  16. Sealing Boot
    • Align the positioning arrow to the "12 o'clock position".
  17. Steering Intermediate Shaft
  18. Bolt
    • 30 Nm +90°
    • Always replace if removed
    • The threaded hole for the bolt must always be cleaned (for example, using a thread tap).
scientia non olet · About LEMON Manuals