Hid Headlamp, Adjusting (Through My 2012)
Checking and adjusting conditions:
- Tire pressure is OK.
- The headlamp lens must be clean and dry.
- The headlamp lens may not be damaged.
- Headlamp reflectors and bulbs are OK.
Vehicle load on driver's seat in otherwise unloaded vehicle (curb weight).
- One person or 75 kg.
The curb weight is the weight of the operational vehicle with completely full fuel tank, including the weight of all equipment carried in operation.
- Fuel tank: at least 90% full.
- Equipment: for example, spare wheel, tools, vehicle jack, fire extinguisher, etc.
If the fuel tank is not at least 90% full, the load must be created as follows.
-- Check fuel tank fill lever in instrument cluster tank gauge and compare with the following table. Place additional weight in the luggage compartment, if necessary.
| Fuel gauge | Additional weight in kg |
|---|---|
| 1/4 | 45 |
| 1/2 | 30 |
| 3/4 | 15 |
| full | 0 |
| Example: if the fuel tank is half full, an additional 30 kg must be placed in the luggage compartment. | |
Use fuel containers filled with water as additional weight (a five liter fuel container filled with water weighs five kg).
- Roll the vehicle several yards or move it back and forth several times to seat the springs.
- The electromechanical parking brake must not be engaged so vehicle is not under stress.
- The vehicle and headlamp adjusting unit must be on a level surface.
- The headlamp adjusting unit must be aligned to the vehicle. Refer to the Headlamp Adjusting Unit Instructions.
- The headlamp adjuster must be distance -a- 30 to 70 cm in front of the headlamp and should not deviate more than dimension -b- = 3 cm from the headlamp center point.
- The inclination dimension is set on the headlamp adjusting unit. Refer to the Headlamp Adjusting Unit Operating Instructions.
- The angle dimension -arrow- is stamped on the upper edge of the headlamp -1- in "%".
The headlamp must be adjusted according to the angle dimension stamped on the headlamp.
The percentage indicator is based on a 10 meter projection distance. Example: At an angle dimension of 1.0%, converts to 10 cm.
Procedure
-- The vehicle must be standing on a flat surface.
-- Turn the headlamp switch to "low beam" - not "Auto".
-- Close all the doors and the rear lid and keep them closed for the duration of the testing/adjusting procedure.
-- Connect the Vehicle Diagnostic Tester.
-- Choose operation mode Diagnosis and start the diagnosis.
-- Select the tab test plan .
-- Select select individual tests and choose the following sequence.
- Body
- Electrical Equipment
- 01 - OBD-capable systems
- 55 - Cornering Lamp and Headlamp Range Control Module (with AFS) J745
- 55 - Headlamp range control, functions
- 55 - Basic setting
The headlamps move into the basic setting with this program.
-- During the program, you will be asked to perform a headlamp adjustment.
Headlamp adjustment
- The horizontal light-dark border must touch the dividing line -1- on the adjusting unit test surface.
- The point -2- between the left horizontal part and the right vertical part of the light-dark border must run vertically through the central mark -3-. The bright core of the light beam must be to the right of the vertical.
To determine the point -2- more easily, cover and uncover the left half of the headlamp several times. Then check low beam again.
After correct headlamp adjustment, the center of the high beam light beam must be on the central marking -3-.
-- To adjust the height of the headlamp, set the light-dark border just under the dividing line with the adjustment screw -1-.
-- Then adjust the light-dark border, starting from the bottom, on the dividing line.
-- For side adjustment, turn the adjusting screw -2-.
The allocation on the right headlamp is reversed.
-- After the headlamp is adjusted, complete the "Basic setting". Switch off the ignition and disconnect the diagnostic connector.