Engine compartment, left side
1 - Fuel injectors, Cylinder bank 2
- Cylinder 4 Fuel Injector N33
- Cylinder 5 Fuel Injector N83
- Cylinder 6 Fuel Injector N84
- Removing and installing → Fuel injectors, removing and installing
2 - Intake Manifold Runner Position Sensor 2 G512
- Component location Component location under intake manifold, cylinder bank 2 (left)
- After replacing, adapt in "Guided Fault-Finding" operating mode under "Adapting intake manifold runner position sensor"
3 - Engine speed (RPM) sensor G28
- Component location → Location Engine Speed (RPM) Sensor G28
4 - Left holder for connectors
- Connector locations Left holder for connectors on bulkhead
5 - Instrument cluster
- With Malfunction Indicator Lamp (MIL) K83 and Electronic Power Control (EPC) Warning Lamp K132
6 - Throttle Position (TP) Sensor G79/Accelerator Pedal Position Sensor 2 G185
- In accelerator pedal module, component location → Location Throttle Position (TP) Sensor G79/Accelerator Pedal Position Sensor 2 G185
7 - Brake light switch F/Brake pedal switch F47 and Clutch pedal switch F36
- Component location → Installed location Brake light switch F/Brake pedal switch F47 , Clutch pedal switch F36
8 - Clutch Pedal Starter Interlock Switch F194
- Component location → Clutch Pedal Starter Interlock Switch F194
9 - SIMOS Control Module J361
- Component location → Component location SIMOS Control Module J361
- Removing and installing → Engine Control Module (ECM), removing and installing
- After replacement, adapt throttle valve control module in operating mode "Guided Fault-Finding" in "Adapting throttle valve control module"
- After replacement on vehicles with automatic transmissions, also perform kick-down adaptation in the operating mode "Guided Fault-Finding" in "Kick-down adaptation"
10 - Oxygen Sensor (O2S) 2 Behind Three Way Catalytic Converter (TWC) G131
- Component location Oxygen sensors location, cylinder bank 2 (left)
- Connector location Left holder for connectors on bulkhead
- Removing and installing → Oxygen sensor behind catalytic converter, bank 2 (left side), removing and installing
11 - Camshaft Adjustment Valve 2 N208
Component location Hall sensor and valve for camshaft adjustment, bank 2
12 - Heated Oxygen Sensor (HO2S) 2 G108
- Component location Oxygen sensors location, cylinder bank 2 (left)
- Connector location Left holder for connectors on bulkhead
- Removing and installing → Oxygen sensor before catalytic converter, bank 2 (left side), removing and installing
13 - Camshaft Adjustment Valve 2 (exhaust) N319
- Component location Hall sensor and valve for camshaft adjustment, bank 2
14 - Camshaft position (CMP) sensor 4 G301
- Component location Hall sensor and valve for camshaft adjustment, bank 2
15 - Left Electro-Hydraulic Engine Mount Solenoid Valve N144
- Only vehicles with automatic transmission
- Component location or under Left Electro-Hydraulic Engine Mount Solenoid Valve N144 or Right Electro-Hydraulic Engine Mount Solenoid Valve N145 installation location
16 - Ignition coils, Cylinder bank 2
- Ignition Coil 4 with Power Output Stage N292
- Ignition Coil 5 with Power Output Stage N323
- Ignition Coil 6 with Power Output Stage N324
- Removing and installing → Ignition coils, removing and installing
17 - Camshaft position (CMP) sensor 2 G163
- Component location Hall sensor and valve for camshaft adjustment, bank 2
18 - High pressure pump
- With Fuel Metering Valve N290
- Component location Component location on the high pressure pump
19 - Fuel Pressure Sensor G247
- Component location Component location under intake manifold, cylinder bank 2 (left)
20 - Knock sensor 2 G66
- Component location Component location under intake manifold, cylinder bank 2 (left)
- Connector location Electrical connectors on left rear of engine