CAN-Bus Terminal Resistance, Transmission Control Module (TCM) J217 to Engine Control Module (ECM) J220, Checking

The Motronic Engine Control Module (ECM) J220 communicates with all databus capable control modules via a CAN databus.

These databus capable control modules are connected via two data bus wires which are twisted together (CAN_High and CAN_Low), and exchange information (messages). Missing information on the databus is recognized as a malfunction and stored.

Trouble-free operation of the CAN-bus requires that it have a terminal resistance. The central terminal resistor is located in the Engine Control Module (ECM) J220.

Special tools, testers and auxiliary items required 

• Multimeter.
• Wiring diagram.

Test requirement 

• A CAN-Bus malfunction was recognized.
• The Engine Control Module (ECM) J220 fuses OK.
• Battery voltage at least 12.5 V.
• Ignition switched off.

Removal 

• Remove the center dash panel - 1  - in the direction of the - arrow  -.

Fig 1: Identifying Right Upper Dashboard Panel

Courtesy of VOLKSWAGEN UNITED STATES, INC.

• Remove the right upper dashboard panel.

Fig 2: Identifying Three Center Screws

Courtesy of VOLKSWAGEN UNITED STATES, INC.

• Remove the three center screws - 1  -

Fig 3: Removing Right Upper Dashboard Panel

Courtesy of VOLKSWAGEN UNITED STATES, INC.

• Remove the right upper dashboard panel - 1  - in the direction of - arrow A  - and - arrow B  -.

Fig 4: Removing TCM Mounting Bolt

Courtesy of VOLKSWAGEN UNITED STATES, INC.

• Remove the retaining screw - arrow  -.

• Using a Multimeter, check the Transmission Control Module (TCM) J217 electrical harness connector terminals 3 to 25 for resistance.

Specified value: 60 to 72 Ω (at approx. 20°C)

If the specified value was not obtained:

• Check the wiring connection for an open circuit, short circuit to Battery (+) or Ground (GND).
• Check the wiring connection for damage, corrosion, lose or broken terminals.
• If necessary, repair the faulty wiring connection.

If no malfunction is found in the wiring:

• Replace the Engine Control Module (ECM) J220. Refer to → Motronic Engine Control Module (ECM) J220, Replacing .

If the specified value was obtained:

Checking wiring 

• Install the Adapter F/VAG1598 (68 Pin) VAG1598/22. Refer to
  • for 5 SPD. AUTOMATIC TRANSMISSION 01V
  • for 5 SPD. AUTOMATIC TRANSMISSION 01V FRONT AND ALL WHEEL DRIVE - INTERNAL COMPONENTS, SERVICING
  • for 6 SPD. AUTOMATIC TRANSMISSION 09L ALL WHEEL DRIVE
  .

If the manufacturers test box is not being used, perform the following step.

• Remove the Engine Control Module (ECM) J220. Refer to → Motronic Engine Control Module (ECM) J220, Replacing .
• Using a Multimeter, check the Transmission Control Module (TCM) J217 electrical harness connector to the Engine Control Module (ECM) J220 electrical harness connector T94 for resistance.

Specified value: 1.5 Ω Max.

If the specified value was not obtained:

• Check the wiring connection for an open circuit, short circuit to Battery (+) or Ground (GND).
• Check the wiring connection for damage, corrosion, lose or broken terminals.
• If necessary, repair the faulty wiring connection.

If no malfunction is found in the wiring:

• Replace the Transmission Control Module (TCM) J217. Refer to → Transmission Control Module (TCM) J217, Replacing .

Final procedures 

After the repair work, the following work steps must be performed in the following sequence:

1. Check the DTC memory.
2. If necessary, erase the DTC memory. Refer to Diagnostic Mode 04 - Reset/Delete Diagnostic Data .
3. If the DTC memory was erased, generate readiness code. Refer to Readiness Code Description .

• End of diagnosis.