Overview - Coolant Pipes
WARNING: This page is about a different car, the 2012 Volkswagen Touareg and 2011 Volkswagen Touareg. However, it is still accessible from the selected car via links, so may be relevant.
Part 1
NOTE:
A vehicle with engine code CATA is shown in the illustration.
On vehicles with CASA and CASD engine codes, they will look different than what is in the illustration.
- O-Ring
- Replace
- Bolt
- 9 Nm
- Right Coolant Pipe
- Removing and installing. Refer to RIGHT COOLANT PIPE, REMOVING AND INSTALLING .
- Bolt
- 23 Nm
- Seal
- Replace
- Bleed Screw
- 9 Nm
- Engine Lifting Eye
- Bolt
- 9 Nm
- Bolt
- 9 Nm
- Connection
- O-Ring
- Replace
- Upper Right Coolant Pipe
- Removing and installing. Refer to UPPER RIGHT COOLANT PIPE, REMOVING AND INSTALLING .
- Bolt
- Engine Cover Bolt
- 5 Nm
- O-Ring
- Replace
- Connection
- Bolt
- 9 Nm
- Engine Coolant Temperature Sensor -G62-
- 2 Nm
- Removing and installing. Refer to Engine Coolant Temperature Sensor -G62-, REMOVING AND INSTALLING .
- O-Rings
- Replace
- Note the different diameter
- Rear Coolant Pipe
- For removing and installing on engine code CATA. Refer to REAR COOLANT PIPE, REMOVING AND INSTALLING .
- Different versions, allocation Parts Information
- Bolt
- 9 Nm
- O-Ring
- Replace
- Installed only on vehicles with engine code CATA
- Bolt
- 9 Nm
- Installed only on vehicles with engine code CATA
- Left Rear Coolant Pipe to Exhaust Gas Recirculation Cooler
- Removing and installing. Refer to LEFT REAR COOLANT PIPE ON EGR AUXILIARY COOLER, REMOVING AND INSTALLING .
- Installed only on vehicles with engine code CATA
- Bolt
- 9 Nm
- Installed only on vehicles with engine code CATA
- O-Ring
- Replace
- Installed only on vehicles with engine code CATA
- Left Rear Coolant Pipe on the Transmission
- For removing and installing on engine code CATA. Refer to LEFT REAR COOLANT PIPE ON TRANSMISSION, REMOVING AND INSTALLING .
- Different versions, allocation Parts Information
- Bolt
- 9 Nm
- Bolt
- 9 Nm
- Upper Coolant Pipe
- Removing and installing. Refer to UPPER COOLANT PIPE, REMOVING AND INSTALLING .
- Bolt
- 9 Nm
- O-Ring
- Replace
Part 2
NOTE:
A vehicle with engine code CATA is shown in the illustration.
On vehicles with CASA and CASD engine codes, they will look different than what is in the illustration.
- Seals
- Replace
- Banjo Bolt
- 15 Nm
- Bolt
- 9 Nm
- Coolant Line
- To the cylinder heads
- Coolant Hose
- From the exhaust gas recirculation coolant thermostat
- Installed only on vehicles with engine code CATA
- Seal
- Replace
- Bleed Screw
- 9 Nm
- Engine Cover Bolt
- 5 Nm
- Upper Left Coolant Pipe
- For removing and installing on engine code CATA. Refer to LEFT UPPER COOLANT PIPE, REMOVING AND INSTALLING .
- Bolt
- 9 Nm
- Left Rear Coolant Pipe
- For removing and installing on engine code CATA. Refer to LEFT REAR COOLANT PIPE, REMOVING AND INSTALLING [CATA] .
- Bolt
- 9 Nm
- Bolt
- 9 Nm
- Bolt
- 9 Nm
- Left Coolant Pipe
- Removing and installing. Refer to LEFT COOLANT PIPE, REMOVING AND INSTALLING .
- Bolt
- 9 Nm
- O-Ring
- Replace