Overview - Hid Headlamp With Dynamic High Beam Control, Through My 2014

WARNING: This page is about a different car, the 2014 Volkswagen Touareg, 2013 Volkswagen Touareg, 2012 Volkswagen Touareg, and 2011 Volkswagen Touareg. However, it is still accessible from the selected car via links, so may be relevant.

NOTE:

Check for possible influences upon the headlamp adjustment, check the adjustment itself, and if needed, adjust the headlamps. Refer to => 29.1.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

1 -
Left Position Lamp Bulb -M1- or Right Position Lamp Bulb -M3-
- Replacing. Refer to POSITION LAMP BULB, REPLACING .
2 -
Left Front Turn Signal Bulb -M5- and Right Front Turn Signal Bulb -M7-
- Bulb 12V, PSY24W SV
- Replacing. Refer to FRONT TURN SIGNAL BULB, REPLACING .
3 -
Lamp Socket with Grip
- For Left Front Turn Signal Bulb -M5- and Right Front Turn Signal Bulb -M7-
4 -
Cap
5 -
Screws
- For attaching the left or right HID lamp control module to the cap -item 4-
6 -
Left HID Headlamp Control Module -J343- or Right HID Headlamp Control Module -J344-

NOTE:
The Left HID Headlamp Control Module -J343- and Right HID Headlamp Control Module -J344- is not capable of On Board Diagnostic (OBD).
- Removing and installing. Refer to HID HEADLAMP CONTROL MODULE
7 -
Screws
- For attaching the headlamp power output stage to the cap
8 -
Left Headlamp Power Output Stage -J667- or Right Headlamp Power Output Stage -J668-
- Removing and installing. Refer to HEADLAMP POWER OUTPUT STAGE, REMOVING AND INSTALLING
  NOTE:
  The cornering lamp and headlamp range control module must be coded after installing a new Headlamp Power Output Stage -J746- and then perform a basic setting for the headlamp. Refer to the => 29.1.
9 -
Cap
10 -
Left HID Headlamp Bulb -L13- or Right HID Headlamp Bulb -L14- ("Bi-Xenon")

WARNING:
Note usage and safety notes for HID headlamp bulbs. Refer to HID HEADLAMP USAGE AND SAFETY PRECAUTIONS .
- Type D3S, 35W
- Replacing. Refer to HID HEADLAMP BULB, REPLACING .
11 -
Left Headlamp Beam Adjustment Motor -V48- or Right Headlamp Beam Adjustment Motor -V49-
- Removing and installing. Refer to HEADLAMP RANGE CONTROL POSITIONING MOTOR, REMOVING AND INSTALLING
12 -
Headlamp
- Removing and installing. Refer to HEADLAMP, REMOVING AND INSTALLING
- Correcting installation position of headlamp. Refer to HEADLAMP INSTALLED POSITION, CORRECTING .
- Headlamp mounting tabs, servicing. Refer to HEADLAMP MOUNTING TABS, SERVICING .
- Perform a basic setting on the headlamp. Refer to => 29.1.
13 -
Adjustment Bushing
- Correcting installation position of headlamp. Refer to HEADLAMP INSTALLED POSITION, CORRECTING .
14 -
Screws
- 5 Nm
- For attaching the headlamp
15 -
Cornering Lamp and Headlamp Range Control Module -J745-
- Bolt tightening specification: 2 Nm
- Component location: on a cross bar in the center of the instrument panel behind the "RCD 550" radio/Front Information Display Control Head -J685-
- Removing and Installing. Refer to Cornering Lamp and Headlamp Range Control Module -J745-, REMOVING AND INSTALLING .
- Coding. Refer to Cornering Lamp and Headlamp Range Control Module -J745-, CODING .
- Output diagnostic test mode. Refer to Cornering Lamp and Headlamp Range Control Module -J745-, OUTPUT DIAGNOSTIC TEST MODE .
  NOTE:
  It is necessary to perform a basic setting on the headlamp if the Cornering Lamp and Headlamp Range Control Module -J745- was coded. Refer to => 29.1.
16 -
Screw
- 5 Nm