APIM DTC Chart
WARNING: This page is about a different car, the 2018 Lincoln Navigator. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. Refer to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| B108E:01 | Display: General Electrical Failure | GO to Pinpoint Test L |
| B108E:02 | Display: General Signal Failure | GO to Pinpoint Test L |
| B108E:4A | Display: Incorrect Component Installed | INSTALL the correct FDIM as necessary. Refer to: Front Display Interface Module (FDIM) . |
| B108E:4B | Display: Over Temperature | GO to Pinpoint Test L |
| B108E:87 | Display: Missing Message | GO to Pinpoint Test L |
| B119F:01 | GPS Antenna: General Electrical Failure | GO to Pinpoint Test S |
| B119F:13 | GPS Antenna: Circuit Open | GO to Pinpoint Test S |
| B1252:11 | USB Port: Circuit Short To Ground | GO to Pinpoint Test P |
| B1252:13 | USB Port: Circuit Open | GO to Pinpoint Test P |
| B14FD:11 | External Media Control Connectivity: Circuit Short To Ground | GO to Pinpoint Test P |
| B1D79:11 | Microphone Input: Circuit Short To Ground | GO to Pinpoint Test O |
| B1D79:12 | Microphone Input: Circuit Short To Battery | GO to Pinpoint Test O |
| B1D79:13 | Microphone Input: Circuit Open | GO to Pinpoint Test O |
| C1001:01 | Vision System Camera: General Electrical Failure | REFER to: Parking Aid . |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test Z |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AA |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AC |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AD |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test AE |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AG |
| U0196:00 | Lost Communication With Entertainment Control Module-Rear "A": No Sub Type Information | GO to Pinpoint Test AH |
| U0198:00 | Lost Communication With Telematic Control Module: No Sub Type Information | GO to Pinpoint Test AI |
| U0208:00 | Lost Communication With "Seat Control Module A": No Sub Type Information | GO to Pinpoint Test AJ |
| U020C:00 | Lost Communication with Wireless Accessory Charging Module "A": No Sub Type Information | GO to Pinpoint Test AK |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module - Left: No Sub Type Information | GO to Pinpoint Test AL |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module - Right: No Sub Type Information | GO to Pinpoint Test AM |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to Pinpoint Test AO |
| U023B:00 | Lost Communication With Image Processing Module B: No Sub Type Information | GO to Pinpoint Test AP |
| U024B:00 | Lost Communication with Seat Control Module "G": No Sub Type Information | GO to Pinpoint Test AQ |
| U024C:00 | Lost Communication with Seat Control Module "H": No Sub Type Information | GO to Pinpoint Test AR |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test AT |
| U0415:00 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information |
NOTE:
If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. DIAGNOSE any Diagnostic Trouble Codes (DTCs) present in the ABS module. Refer to: Anti-Lock Brake System (ABS) and Stability Control
. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information |
NOTE:
If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. DIAGNOSE any Diagnostic Trouble Codes (DTCs) present in the BCM. Refer to: Body Control Module (BCM)
. |
| U0423:00 | Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information |
NOTE:
If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. DIAGNOSE any Diagnostic Trouble Codes (DTCs) present in the IPC. Refer to: Instrumentation, Message Center and Warning Chimes
. |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information |
NOTE:
If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. DIAGNOSE any Diagnostic Trouble Codes (DTCs) present in the RCM. Refer to: Airbag Supplemental Restraint System (SRS)
. |
| U1018:00 | Lost Communication With Generic Function Module: No Sub Type Information | GO to Pinpoint Test AU |
| U1A00:87 | Private Communication Network: Missing Message | GO to Pinpoint Test T |
| U2017:45 | Control Module Software #2: Program Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to APIM GUIDED ROUTINE TESTING -- NAVIGATOR . |
| U2017:51 | Control Module Software #2: Not Programmed | This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. Refer to: SYNC Module [APIM] Programming . |
| U2017:52 | Control Module Software #2: Not Activated | This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. Refer to: SYNC Module [APIM] Programming . |
| U2017:54 | Control Module Software #2: Missing Calibration | This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. Refer to: SYNC Module [APIM] Programming . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. Refer to: SYNC Module [APIM] Programming . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. Refer to: SYNC Module [APIM] Programming . |
| U3000:04 | Control Module: System Internal Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to APIM GUIDED ROUTINE TESTING -- NAVIGATOR . . |
| U3000:09 | Control Module: Component Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to APIM GUIDED ROUTINE TESTING -- NAVIGATOR . . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to APIM GUIDED ROUTINE TESTING -- NAVIGATOR . . |
| U3000:88 | Control Module: Bus Off |
NOTE:
The module was unable to communicate on the network at a point in time. The fault is not currently present since the module had to communicate with the diagnostic scan tool to report this DTC. INSPECT for damaged or corroded wiring at the APIM. Refer to Wiring Diagrams Module Communications Network
for schematic and connector information. CLEAR the DTC. WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to APIM GUIDED ROUTINE TESTING -- NAVIGATOR
.
.| |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AV |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AW |