LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2016 >> S5 Prestige, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 1029 (Glass & Window System (Service Information)) >> 64 Glass, Window Regulators >> Rear Window >> Rear Window, Removing And Installing >> Undamaged Rear Window, Removing, AVANT

Undamaged Rear Window, Removing, AVANT

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2018 Audi S6, 2018 Audi A6 Quattro, 2018 Audi A6, 2017 Audi S6, and 2017 Audi A6 Quattro. However, it is still accessible from the selected car via links, so may be relevant.

Procedure 

-- Remove the rear lid trim panel. Refer to UPPER REAR LID TRIM PANEL, REMOVING AND INSTALLING

-- Remove the roof edge spoiler. Refer to ROOF EDGE SPOILER, REMOVING AND INSTALLING .

-- Remove the rear window wiper motor. Refer to appropriate service information. .

-- Disconnect rear window defroster and window antenna connectors and secure to center of window with adhesive tape.

WARNING:

When removing a window glass, always wear protective eyewear and leather gloves.

-- Unroll with the :VAS6452/1  approximately 6.5 meters of cutting wire (approximately six turns) and cut it.

-- Cover the area where the awl comes out under the body flange with adhesive tape -1- to prevent damaging it.

GWWA64-10288Courtesy of AUDI OF AMERICA, LLC

-- Thread both cutting wire ends -3- into the awl -2- and pull it toward the inside.

-- Place the cutting wire all the way around under the windshield as shown.

GWWA64-10289Courtesy of AUDI OF AMERICA, LLC

-- Route the cutting wire around the rear window under the window glass as shown.

CAUTION:

The wire ends must not be twisted on the adhesive bead pass-through -arrow-.

-- Mount both reel devices on the inside of the windshield as shown.

GWWA64-10290Courtesy of AUDI OF AMERICA, LLC

-- Insert the cutting wire end -1- into the reel device -2-.

GWWA64-10228Courtesy of AUDI OF AMERICA, LLC

-- Tension the cutting wire using the reel device -1- and insert the plastic film -2- taken from the :VAS6452  to protect between the wire and the window glass.

GWWA64-10291Courtesy of AUDI OF AMERICA, LLC

-- Cut free the first section, while doing this, the wire is guided into the integrated idler roller -arrow- from the reel device.

GWWA64-10229Courtesy of AUDI OF AMERICA, LLC

-- Insert an additional guide awl -2- into the adhesive and secure it to the windshield with the suction cup to make sure that the wire runs as close to the windshield as possible.

GWWA64-10292Courtesy of AUDI OF AMERICA, LLC

-- Move the reel device and the guide awl as shown and cut free the section along the >>D-pillar<<.

GWWA64-10293Courtesy of AUDI OF AMERICA, LLC

-- Continue cutting the window glass free until about the center of the window glass is reached.

GWWA64-10294Courtesy of AUDI OF AMERICA, LLC

-- Use the second reel device to cut the lower section of the window glass free.

GWWA64-10295Courtesy of AUDI OF AMERICA, LLC

-- Move the reel device upward and insert the guide awl as shown.

GWWA64-10296Courtesy of AUDI OF AMERICA, LLC

-- Cut the window glass out by moving upward along the >>D-pillar<<.

GWWA64-10297Courtesy of AUDI OF AMERICA, LLC

-- Move the reel device over the center of the window glass and over the first reel device as shown and cut free the window glass along the top.

GWWA64-10298Courtesy of AUDI OF AMERICA, LLC

-- Remove the window glass with suction lifter.