Overview - Transverse Link

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2018 Audi S6, 2018 Audi A6 Quattro, 2018 Audi A6, 2017 Audi S6, and 2017 Audi A6 Quattro. However, it is still accessible from the selected car via links, so may be relevant.

Fig 1: Transverse Link Exploded View

Courtesy of AUDI OF AMERICA, LLC

Tie Rod
- Removing and installing. Refer to TIE ROD, REMOVING AND INSTALLING .
- There are different versions and installed positions. For the correct allocation. Refer to the Parts information.
Eccentric Bolt
- Always replace if removed
- Tighten either in the curb weight position (refer to WHEEL BEARING IN CURB WEIGHT, LIFTING VEHICLES WITH COIL SPRING ) or in the control position (refer to WHEEL BEARING IN CONTROL POSITION, LIFTING VEHICLES WITH AIR SUSPENSION ).
Eccentric Washer
Nut
- 95 Nm
- Always replace if removed
Bolt
- 70 Nm +180° turn
- Always replace if removed
- Tighten either in the curb weight position (refer to WHEEL BEARING IN CURB WEIGHT, LIFTING VEHICLES WITH COIL SPRING ) or in the control position (refer to WHEEL BEARING IN CONTROL POSITION, LIFTING VEHICLES WITH AIR SUSPENSION ).
Nut
- Always replace if removed
Bracket
- For the Left Rear Level Control System Sensor -G76- / Right Rear Level Control System Sensor -G77-
Bolt
- 70 Nm +180° turn
- Always replace if removed
- Tighten either in the curb weight position (refer to WHEEL BEARING IN CURB WEIGHT, LIFTING VEHICLES WITH COIL SPRING ) or in the control position (refer to WHEEL BEARING IN CONTROL POSITION, LIFTING VEHICLES WITH AIR SUSPENSION ).
Subframe
Nut
- Always replace if removed
Upper Transverse Link
- Removing and installing. Refer to UPPER TRANSVERSE LINK, REMOVING AND INSTALLING .
Shim
Nut
- 95 Nm
- Always replace if removed
- Tighten either in the curb weight position (refer to WHEEL BEARING IN CURB WEIGHT, LIFTING VEHICLES WITH COIL SPRING ) or in the control position (refer to WHEEL BEARING IN CONTROL POSITION, LIFTING VEHICLES WITH AIR SUSPENSION ).
Adjusting Bolt
Bolt
- 70 Nm +180° turn
- Always replace if removed
- Tighten either in the curb weight position (refer to WHEEL BEARING IN CURB WEIGHT, LIFTING VEHICLES WITH COIL SPRING ) or in the control position (refer to WHEEL BEARING IN CONTROL POSITION, LIFTING VEHICLES WITH AIR SUSPENSION ).
Lower Transverse Link
- Removing and installing. Refer to LOWER TRANSVERSE LINK, REMOVING AND INSTALLING .
Bolt
- 120 Nm +360° turn
- Always replace if removed
- Tighten either in the curb weight position (refer to WHEEL BEARING IN CURB WEIGHT, LIFTING VEHICLES WITH COIL SPRING ) or in the control position (refer to WHEEL BEARING IN CONTROL POSITION, LIFTING VEHICLES WITH AIR SUSPENSION ).
  NOTE:
  Axle alignment is necessary if the bolt is loosened.
Cap
Wheel Bearing Housing
Spacer Tube
- Always replace if removed
Nut
- Always replace if removed
  CAUTION:
  - Do not tighten the threaded connection using the nut.
  NOTE:
  Axle alignment is necessary if the nut is loosened.
Bolt
- 90 Nm +90° turn
- Always replace if removed
- Tighten either in the curb weight position (refer to WHEEL BEARING IN CURB WEIGHT, LIFTING VEHICLES WITH COIL SPRING ) or in the control position (refer to WHEEL BEARING IN CONTROL POSITION, LIFTING VEHICLES WITH AIR SUSPENSION ).

Courtesy of AUDI OF AMERICA, LLC

A - Steel tie rod

B - Aluminum cast tie rod

1 - Installed position: The marking must be on the outside and the tip of the triangle points up.

Courtesy of AUDI OF AMERICA, LLC

Installed position: The marking must be on the outside and the horizontal line points up.
Aluminum cast tie rod