Overview - Wheel Bearing Housing, Wheel Bearing Unit And Coil Spring Shock Absorber : Notes
WARNING: This page does not describe the selected car, but rather 13 other vehicles, including the 2017 Audi SQ5, 2017 Audi Q5, 2016 Audi SQ5, 2016 Audi Q5, and 2015 Audi SQ5. However, it is still accessible from the selected car via links, so may be relevant.
- Drive Axle
- There are different versions .
- Backing Plate
- Bolt
- Tightening specification, refer to DRIVE AXLE .
- Upper Transverse Link
- Nut
- 95 Nm
- Always replace if removed
- Must be tightened in the curb weight position, refer to WHEEL BEARING IN CURB WEIGHT, LIFTING VEHICLES WITH COIL SPRING .
- Eccentric Washer
- Bolt
- Bracket
- For the brake hose, brake caliper wiring harness and rear wheel speed sensor wiring harness
- Bolt
- 10 Nm
- Rear Wheel Speed Sensor
- Bolt
- 9 Nm
- Bonded Rubber Bushing
- Cannot be exchanged separately
- Ball BearingCAUTION:
- Avoid contaminating with dirt and damaging the seal when setting down/storing, refer to AVOID CONTAMINATING WITH DIRT AND DAMAGING THE SEAL WHEN SETTING DOWN/STORING .
- Wheel bearing unit, removing and installing, refer to WHEEL BEARING UNIT, REMOVING AND INSTALLING .
- For servicing the wheel bearing unit, refer to WHEEL BEARING UNIT, SERVICING .
- Wheel HubCAUTION:
- Avoid contaminating with dirt and damaging the seal when setting down/storing, refer to AVOID CONTAMINATING WITH DIRT AND DAMAGING THE SEAL WHEN SETTING DOWN/STORING .
- Wheel bearing unit, removing and installing, refer to WHEEL BEARING UNIT, REMOVING AND INSTALLING .
- For servicing the wheel bearing unit, refer to WHEEL BEARING UNIT, SERVICING .
- Brake Shield
- Bolt
- 10 Nm
- Brake Rotor
- Collar Screw
- 200 Nm +180°
- Always replace if removed
- Bolt
- 5 Nm
- Tie Rod
- There are versions made of aluminum and steel.
- A mixed installation is not permitted
- Bolt
- 90 Nm +90°
- Always replace if removed
- Must be tightened in the curb weight position, refer to WHEEL BEARING IN CURB WEIGHT, LIFTING VEHICLES WITH COIL SPRING .
- Bolt
- 120 Nm +360°
- Always replace if removed
- Must be tightened in the curb weight position, refer to WHEEL BEARING IN CURB WEIGHT, LIFTING VEHICLES WITH COIL SPRING .NOTE:
Axle alignment is necessary if the bolt is removed.
- Spacer Tube
- Always replace if removed
- Nut
- Always replace if removedCAUTION:
- Do not tighten the threaded connection using the nut.
NOTE:Axle alignment is necessary if the nut is loosened.
- Always replace if removed
- Lower Transverse Link
- Bonded Rubber Bushing
- Replacing, refer to WHEEL BEARING HOUSING BONDED RUBBER BUSHING, REMOVING AND INSTALLING .
- Wheel Bearing Housing
- Removing and installing, refer to WHEEL BEARING HOUSING, REMOVING AND INSTALLING .
- Bolt
- 80 Nm +90°
- Always replace if removed
- Washer
- Serves as corrosion protection
- Always use
- Bolt
- 150 Nm +180°
- Always replace if removed
- Must be tightened in the curb weight position, refer to WHEEL BEARING IN CURB WEIGHT, LIFTING VEHICLES WITH COIL SPRING .
- Shock Absorber
- Removing and installing, refer to SHOCK ABSORBER .
- Protective Sleeve
- Stop Buffer
- Bolt
- 50 Nm +45°
- Always replace if removed
- Upper Shock Absorber Mount
- Installed position, refer to Figure
- Nut
- 35 Nm
- Always replace if removed
- Protective Cap