Overview - Power Steering Pump, 8-Cylinder FSI, With Dynamic Steering

WARNING: This page does not describe the selected car, but rather 19 other vehicles, including the 2017 Audi S5, 2017 Audi A5 Quattro, 2016 Audi S5, 2016 Audi A5 Quattro, and 2015 Audi S5. However, it is still accessible from the selected car via links, so may be relevant.

Power Steering Pump Assembly Overview

NOTE:

Always replace seals.

Do not reuse fluid you have drained.

Only use Hydraulic Fluid.

When Replacing The Power Steering Pump, replace Its Seal And O-Ring. Refer To the appropriate Service Information .

Only use Grease from the Parts Information. to lubricate.

Fig 1: Power Steering Pump, Vehicles With Dynamic Steering

Courtesy of AUDI OF AMERICA, LLC

Power Steering Pump -V119-
- With Power Steering Pump Regulator Valve -(V119)-
- The power steering pump and the control valve. Refer to -item ) OVERVIEW - POWER STEERING PUMP, 8-CYLINDER FSI, WITH DYNAMIC STEERING - POWER STEERING PUMP REGULATOR VALVE -(V119)- are one component and can only be replaced together.
- Fill with Hydraulic Fluid before installing
- Delivery pressure, checking. Refer to POWER STEERING PUMP DELIVERY PRESSURE, CHECKING, 8-CYLINDER FSI .
- Removing and installing. Refer to REMOVING & INSTALLING POWER STEERING PUMP, VEHICLES WITH DYNAMIC STEERING [CAEB, CPMA] / POWER STEERING PUMP, VEHICLES WITHOUT DYNAMIC STEERING [CAEB, CPMA] / POWER STEERING PUMP, VEHICLES WITH DYNAMIC STEERING [CALA] / POWER STEERING PUMP, VEHICLES WITHOUT DYNAMIC STEERING [CALA] / POWER STEERING PUMP, VEHICLES WITH DYNAMIC STEERING [CCBA, CGXC] / POWER STEERING PUMP, VEHICLES WITHOUT DYNAMIC STEERING [CCBA, CGXC] / POWER STEERING PUMP, VEHICLES WITH DYNAMIC STEERING [CAUA, CFSA] / POWER STEERING PUMP, VEHICLES WITHOUT DYNAMIC STEERING [CAUA, CFSA] .
- Grease the power steering pump splines when installing.
- Bleed the steering. Refer to STEERING, BLEEDING AFTER REPLACING .
- Check hydraulic fluid level. Refer to POWER STEERING FLUID LEVEL, CHECKING .
- Steering System, checking for leaks. Refer to STEERING, CHECKING FOR LEAKS .
Input Shaft
- Grease the splines on the input shaft and power steering pump all the way around. Allocation. Refer to the Parts Information.
- Grease the hole on the pump side and on the engine side or on the end of the shaft. For allocation. Refer to the Parts Information.
Seal
- Replacing. Refer to the appropriate Service Information .
- Grease when installing.
Bolt
- Tightening specification for vehicles with a manual transmission. Refer to TIGHTENING SPECIFICATIONS [0B4] .
- Tightening specification for vehicles with an automatic transmission. Refer to TRANSMISSION TIGHTENING SPECIFICATIONS [0AW] .
- Transmission/engine/power steering pump bolt
Bolt
- 25 Nm
Power Steering Pump Regulator Valve -(V119)-
- The power steering pump and the control valve are one component and can only be replaced together.
Intake Hose
- The "P" marking on the evacuation hose -arrow- must align with the formed seam -arrow- on the power steering pump.
Clamp
- Always replace if removed
- Tension using Hose Clip Pliers:VAG1275A
Pressure Line
CAUTION:
- Insert the pressure line completely when installing.
- Note the installation position: the angle between the line connection and the power steering pump axle must be approximately 53°.
Union Nut
- 38 Nm
Seal
- Always replace if removed