Overview - Power Steering Pump, 6-Cylinder FSI, Without Dynamic Steering

WARNING: This page does not describe the selected car, but rather 19 other vehicles, including the 2017 Audi S5, 2017 Audi A5 Quattro, 2016 Audi S5, 2016 Audi A5 Quattro, and 2015 Audi S5. However, it is still accessible from the selected car via links, so may be relevant.

Power Steering Pump, Removing and Installing, 6-Cylinder FSI Engine, Vehicles without Dynamic Steering. Refer to REMOVING & INSTALLING POWER STEERING PUMP, VEHICLES WITH DYNAMIC STEERING [CAEB, CPMA] / POWER STEERING PUMP, VEHICLES WITHOUT DYNAMIC STEERING [CAEB, CPMA] / POWER STEERING PUMP, VEHICLES WITH DYNAMIC STEERING [CALA] / POWER STEERING PUMP, VEHICLES WITHOUT DYNAMIC STEERING [CALA] / POWER STEERING PUMP, VEHICLES WITH DYNAMIC STEERING [CCBA, CGXC] / POWER STEERING PUMP, VEHICLES WITHOUT DYNAMIC STEERING [CCBA, CGXC] / POWER STEERING PUMP, VEHICLES WITH DYNAMIC STEERING [CAUA, CFSA] / POWER STEERING PUMP, VEHICLES WITHOUT DYNAMIC STEERING [CAUA, CFSA] .

Power Steering Pump Assembly Overview

NOTE:

Always replace seals.

Do not reuse fluid you have drained.

Only use Hydraulic Fluid.

Fig 1: Exploded View Of Power Steering Pump, Vehicles Without Dynamic Steering (6-Cylinder FSI)

Courtesy of AUDI OF AMERICA, LLC

Bracket
Sleeve
- Drive the sleeve back slightly to install the power steering pump.
Bolt
- 20 Nm
Bolt
- 20 Nm
- For securing the bracket to the engine.
- Note the different bolt lengths.
Bolt
- 20 Nm
- For securing the bracket to the engine.
- Note the different bolt lengths.
Clamp
- Always replace if removed
- Tension using Hose Clip Pliers:VAG1275A
Intake Hose
- The "P" marking on the evacuation hose -arrow- must align with the formed seam -arrow- on the power steering pump.
Seal
- Always replace if removed
Pressure Line
CAUTION:
- Insert the pressure line completely when installing.
- Depending on the version, also mounted to the A/C compressor
Bolt
- 9 Nm
Power Steering Pump
- Allocation. Refer to the Parts Information.
- Fill with Hydraulic Fluid before installing
- Delivery pressure, checking. Refer to POWER STEERING PUMP DELIVERY PRESSURE, CHECKING, 6-CYLINDER FSI .
- Removing and installing. Refer to REMOVING & INSTALLING POWER STEERING PUMP, VEHICLES WITH DYNAMIC STEERING [CAEB, CPMA] / POWER STEERING PUMP, VEHICLES WITHOUT DYNAMIC STEERING [CAEB, CPMA] / POWER STEERING PUMP, VEHICLES WITH DYNAMIC STEERING [CALA] / POWER STEERING PUMP, VEHICLES WITHOUT DYNAMIC STEERING [CALA] / POWER STEERING PUMP, VEHICLES WITH DYNAMIC STEERING [CCBA, CGXC] / POWER STEERING PUMP, VEHICLES WITHOUT DYNAMIC STEERING [CCBA, CGXC] / POWER STEERING PUMP, VEHICLES WITH DYNAMIC STEERING [CAUA, CFSA] / POWER STEERING PUMP, VEHICLES WITHOUT DYNAMIC STEERING [CAUA, CFSA] .
- Bleed the steering. Refer to STEERING, BLEEDING AFTER REPLACING .
- Check hydraulic fluid level. Refer to POWER STEERING FLUID LEVEL, CHECKING .
- Steering System, checking for leaks. Refer to STEERING, CHECKING FOR LEAKS .
Belt Pulley
Bolt
- 22 Nm
Bolt
- 20 Nm
- For securing the power steering pump to the bracket
Bolt
- 20 Nm
- For securing the bracket to the engine.