Set The Cylinder Head In Place.

-- Set The Cylinder Head In Place. 

LEFT CYLINDER HEAD: 

Fig 1: Identifying Unloaded Camshaft Slider & Bolts (Left Cylinder Head)

Courtesy of AUDI OF AMERICA, LLC

-- Insert the bolts -1 through 7- while sliding the unloaded camshaft slider -A- accordingly.

-- Tighten the bolts in 3 steps following the sequence -1 to 7-. Refer to OVERVIEW - CYLINDER HEAD .

RIGHT CYLINDER HEAD: 

Fig 2: Identifying Unloaded Camshaft Slider & Bolts (Right Cylinder Head)

Courtesy of AUDI OF AMERICA, LLC

-- Insert the bolts -8 through 14- while sliding the unloaded camshaft sliders -D- and -E- accordingly.

-- Tighten the bolts in 3 steps following the sequence -8 to 14-. Refer to OVERVIEW - CYLINDER HEAD .

CONTINUATION FOR BOTH CYLINDER HEADS: 

Fig 3: Identifying TDC With Special Tool Adapter T140058

Courtesy of AUDI OF AMERICA, LLC

-- Position the camshaft timing chain on the camshafts. Refer to Installing .

-- Remove the Camshaft Clamp:T40133  and the Crankshaft Locking Pin:T40069  .

-- Turn the crankshaft one full revolution (360°) in the direction of engine rotation -arrow- using the Crankshaft Socket:T40058  .

• The openings -arrows- on the exhaust camshafts must face toward the outer side of the engine.
  Fig 4: Identifying Exhaust Camshaft Openings Alignment

  Courtesy of AUDI OF AMERICA, LLC

LEFT CYLINDER HEAD: 

Fig 5: Slide Unloaded Camshaft Sliders As Far As The Stop In Direction Of -Arrow-

Courtesy of AUDI OF AMERICA, LLC

-- Slide the unloaded camshaft sliders -B- and -C- as far as the stop in the direction of the -arrow-.

RIGHT CYLINDER HEAD: 

Fig 6: Slide Unloaded Camshaft Slide As Far As Stop In Direction

Courtesy of AUDI OF AMERICA, LLC

-- Slide the unloaded camshaft slider -F- as far as the stop in the direction of the -arrow-.

CONTINUATION FOR BOTH CYLINDER HEADS: 

Fig 7: Identifying TDC With Special Tool Adapter T140058

Courtesy of AUDI OF AMERICA, LLC

-- Turn the crankshaft one full revolution (360°) in the direction of engine rotation -arrow- using the Crankshaft Socket:T40058  .

• The threaded holes -arrows- in the camshafts must face upward.
  Fig 8: Identifying Camshaft Threaded Hole Alignment

  Courtesy of AUDI OF AMERICA, LLC

LEFT CYLINDER HEAD: 

Fig 9: Identifying Bolt

Courtesy of AUDI OF AMERICA, LLC

-- Insert the bolt -15- and tighten it in 3 steps. Refer to OVERVIEW - CYLINDER HEAD .

RIGHT CYLINDER HEAD: 

Fig 10: Identifying Bolt -16-

Courtesy of AUDI OF AMERICA, LLC

-- Insert the bolt -16- and tighten it in 3 steps. Refer to OVERVIEW - CYLINDER HEAD .

CONTINUATION FOR BOTH CYLINDER HEADS: 

Fig 11: Identifying TDC With Special Tool Adapter T140058

Courtesy of AUDI OF AMERICA, LLC

-- Turn the crankshaft one full revolution (360°) in the direction of engine rotation -arrow- using the Crankshaft Socket:T40058  .

• The openings -arrows- on the exhaust camshafts must face toward the outer side of the engine.
  Fig 12: Identifying Exhaust Camshaft Openings Alignment

  Courtesy of AUDI OF AMERICA, LLC

LEFT CYLINDER HEAD: 

Fig 13: Slide Unloaded Camshaft Slider As Far As Stop In Direction Of -Arrow-

Courtesy of AUDI OF AMERICA, LLC

-- Slide the unloaded camshaft slider -B- as far as the stop in the direction of the -arrow-.

RIGHT CYLINDER HEAD: 

Fig 14: Slide Unloaded Camshaft Sliders As Far As The Stop In Direction Of -Arrow-

Courtesy of AUDI OF AMERICA, LLC

-- Slide the unloaded camshaft slider -F- as far as the stop in the direction of the -arrow-.