LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2016 >> S4 Premium Plus, Standard Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 1214 (Rear Suspension (1 Of 2) (Coupe)) >> 42 Rear Suspension >> Wheel Bearing And Trailing Arm >> Wheel Bearing Housing Bonded Rubber Bushing, Replacing >> Wheel Bearing Housing Rubber Bonded Bushing, Removing And Installing, All Wheel Drive (AWD) Vehicles >> Front Bonded Rubber Bushing, Installing

Front Bonded Rubber Bushing, Installing

WARNING: This page does not describe the selected car, but rather 23 other vehicles, including the 2017 Audi S5, 2017 Audi A5 Quattro, 2016 Audi S5, 2016 Audi A5 Quattro, and 2015 Audi S5. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Front Rubber Bonded Bushing
GWWA42-10293Courtesy of AUDI OF AMERICA, LLC

-- Insert the bonded rubber bushing into the :T40184/3  . The "thin" collar -arrow- must face upward.

In Order To Install The Front Rubber Bonded Bushing, The :T40184/2  -3- Must Be Mounted On The Front Rubber Bonded Bushing In Such A Way So That The Lugs -2- Fit Into The Grooves -4-.

-- Press the front rubber bonded bushing all the way onto the thrust plates -1 and 6-.

Fig 2: Press Front Rubber Bonded Bushing All Way Onto Thrust Plates
GWWA42-10290Courtesy of AUDI OF AMERICA, LLC
  1. :VW401  . Arrange as illustrated.
  2. :T40184/3 
  3. Front bonded rubber bushing
  4. :VW408A 
  5. :T40184/2 
  6. :VW402  . Arrange as illustrated.

-- Then slightly pull apart the thrust plates -1 and 6-.

-- Press the front rubber bonded bushing approximately 2 mm out of the :T40184/3  .

Fig 3: Pressing Front Rubber Bonded Bushing Approximately 2 Mm Out Of T40184/3
GWWA42-10291Courtesy of AUDI OF AMERICA, LLC

a = 2 mm

-- Remove the :VW408A  and insert the :VW411  .

-- Position the wheel bearing housing on the :VAG1290A  .

-- Mount the front rubber bonded bushing (not shown in the illustration), the pressure plate -3- and the sleeve -1- on the wheel housing bearing.

Fig 4: Mount Front Rubber Bonded Bushing
GWWA42-10289Courtesy of AUDI OF AMERICA, LLC
  1. :T40184/3 
  2. :VW411 
  3. :T40184/2  . Pay attention to the installation position of the front rubber bonded bushing.

-- Place the tools on the front bonded rubber bushing and the wheel bearing housing -3- as illustrated.

Fig 5: Placing Tools On Front Bonded Rubber Bushing And Wheel Bearing Housing
GWWA42-10288Courtesy of AUDI OF AMERICA, LLC
NOTE:

When Mounting The Wheel Bearing Housing Onto The :T40184/1  Be Careful Not To Damage Or Push The Rubber Grommet On The Rear Rubber Bonded Bushing.

-- Slowly press the front rubber bonded bushing in (not shown in the illustration) until the sleeve -2- can be pulled out at the top.

  1. :VW411 
  2. :T40184/3 
  3. Wheel bearing housing
  4. :T40184/1  . The side with the groove must face the wheel bearing housing. On a bonded rubber bushing with a "positioning tab", this is in the groove on the :T40184/1  .
  5. :VW402 

Ignore item -3-.

Fig 6: Pressing Front Rubber Bonded Bushing Into Wheel Bearing Housing
GWWA42-10292Courtesy of AUDI OF AMERICA, LLC

-- Slowly press the front rubber bonded bushing -2- so that it is even with the edge -arrow- of the wheel bearing housing.

-- Install the wheel bearing housing. Refer To WHEEL BEARING HOUSING, REMOVING AND INSTALLING, FRONT WHEEL DRIVE (FWD) VEHICLES .

scientia non olet · About LEMON Manuals