Backrest Cover And Cushion, Removing And Installing, Super Sport Seat: Removing

WARNING: This page does not describe the selected car, but rather 23 other vehicles, including the 2017 Audi S5, 2017 Audi A5 Quattro, 2016 Audi S5, 2016 Audi A5 Quattro, and 2015 Audi S5. However, it is still accessible from the selected car via links, so may be relevant.

WARNING:

Follow all Safety Precautions when working with pyrotechnic components. Refer To SAFETY PRECAUTIONS .
Before handling pyrotechnic components (for example, disconnecting the connector), the person handling it must "discharge static electricity". This can be done by touching the door striker, for example.

-- Remove the front seat. Refer To FRONT SEAT, REMOVING AND INSTALLING, POWER .

-- Attach the front seat to the Engine/Transmission Holder - Seat Repair Fixture:VAS6136 . Refer To FRONT SEAT, MOUNTING ON FIXTURE FOR SEAT REPAIR .

Vehicles Equipped With A Mount For A DVD Player:

Fig 1: Identifying Guides And Trim

Courtesy of AUDI OF AMERICA, LLC

DVD player removed.

-- Unclip the trim -2- for the connector -arrow-.

WARNING:

Danger Of Eye Injury.

Wear protective eyewear.

-- Drill out the guides -1 and 3- for the DVD player using a 12 mm diameter drill.

Fig 2: Identifying Drill Bit And Dimension -A- = 35 mm On Guide

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

Danger Of Destroying The Backrest Cover And Cushion.

The guides are held in the backrest frame by the retaining tabs -arrows-.
When removing, drill out only up to dimension -a- = 35 mm.

Continuation For All Vehicles:

-- Remove the backrest cover. Refer To BACKREST COVER, REMOVING AND INSTALLING, TWO PIECE .

-- Remove front backrest. Refer To SEAT PAN, REMOVING AND INSTALLING .

-- Remove the entry assistance trim. Refer To ENTRY ASSISTANCE TRIM, REMOVING AND INSTALLING, POWER STANDARD SEAT .

-- Disengage the lower retaining channels -5 and 6-.

Fig 3: Disengaging Retaining Channels

Courtesy of AUDI OF AMERICA, LLC

-- Disengage The Upper Retaining Channel -3-.

1 - Cover

2 - Backrest frame

4 - Backrest frame trim

-- Disengage The Side Retaining Strips -3- At The Backrest Frame Trim Catches -2-.

Fig 4: Disengaging Side Frame

Courtesy of AUDI OF AMERICA, LLC

1 - Cover

WARNING:

Before Handling Pyrotechnic Components (For Example, Disconnecting The Connector), The Person Handling It Must "Discharge Static Electricity". This Can Be Done By Touching The Door Striker, For Example.

-- Pull the cover as far forward as possible in the side airbag area in order to be able to remove side airbag.

-- Remove the side airbag. Refer To FRONT SIDE AIRBAG WITH IGNITER, REMOVING AND INSTALLING .

-- Remove the airbag from the pocket sewn into the cover and engage the airbag in the backrest frame.

-- Reach from the rear side of the backrest under the padding and find the release button -5-.

Fig 5: Locating Release Button

Courtesy of AUDI OF AMERICA, LLC

-- Press the release button in the direction of the -arrow-.

-- Hold the release button -5- down in this position.

-- Remove the padding with the headrest -1- upward from the backrest frame -3-.

2 - Headrest guide without release button

4 - Side airbag

6 - Headrest guide with release button

NOTE:

A Second Technician Is Needed To Remove The Padding With The Headrest From The Backrest Frame.

Equipment Versions With Lumbar Support:

Fig 6: Locating Velcro (R) Fastener On Lumbar Support

Courtesy of AUDI OF AMERICA, LLC

-- Separate the padding from the Velcro fastener -3- on the lumbar support -2- otherwise the lumbar support will be damaged when removing the hooks -arrows-.

Continuation For All Vehicles:

-- Remove the cover with padding from the backrest frame.