Overview - Hydraulic Line, Reservoir, Vehicles With 6-Cylinder Diesel Engine, Vehicles Without Dynamic Steering

WARNING: This page does not describe the selected car, but rather 23 other vehicles, including the 2017 Audi S5, 2017 Audi A5 Quattro, 2016 Audi S5, 2016 Audi A5 Quattro, and 2015 Audi S5. However, it is still accessible from the selected car via links, so may be relevant.

The power steering pump is not designed to be serviced. If there are customer complaints, the cause must be determined using a pressure and leak test. If there is a malfunction, replace the power steering pump.

NOTE:

If power steering fluid is low in reservoir, check steering system for leaks.

If there are leaks in the area of the line connections, the lines/connections must first be inspected for leaks, tightened as necessary and wiped dry.

The power steering pump is delivered without oil. Before installing, fill pump with Hydraulic Fluid and turn pump by hand. Otherwise, the power steering pump may be noisy when operating or may even be damaged.

Fig 1: Exploded View Of Hydraulic Line, Reservoir, Vehicles With 6-Cylinder Diesel Engine (Vehicles Without Dynamic Steering)

Courtesy of AUDI OF AMERICA, LLC

Tensioning Strap
- Attach to body. Refer to COMPONENT LOCATION OVERVIEW - HYDRAULIC POWER STEERING, VEHICLES WITH 6-CYLINDER DIESEL ENGINE, VEHICLES WITH AND WITHOUT DYNAMIC STEERING .
Reservoir
- Note installed position. Refer to COMPONENT LOCATION OVERVIEW - HYDRAULIC POWER STEERING, VEHICLES WITH 6-CYLINDER DIESEL ENGINE, VEHICLES WITH AND WITHOUT DYNAMIC STEERING .
- Installation position of hoses on the reservoir. Refer to HOSE LINES TO RESERVOIR, HYDRAULIC FLUID COOLER AND RETURN LINE INSTALLED POSITION .
Cap with Dip Stick
- Fluid Level, Checking. Refer to POWER STEERING FLUID LEVEL, CHECKING
Bolt
- 9 Nm
Bolt
- 9 Nm
Spring Clamp
- Remove and install with Hose Clip Pliers:VAG1921
Connector
- For the engine mount
Bolt
- 9 Nm
Retaining Bracket
Nut
- 9 Nm
Seal
- Always replace if removed
Pressure Line
- From the power steering pump to the power steering gear
  CAUTION:
  - Insert The Pressure Line Completely When Installing.
- Mounting on crossbrace. Refer to COMPONENT LOCATION OVERVIEW - HYDRAULIC POWER STEERING, VEHICLES WITH 6-CYLINDER DIESEL ENGINE, VEHICLES WITH AND WITHOUT DYNAMIC STEERING
- Wiring connection installation location. Refer to COMPONENT LOCATION OVERVIEW - HYDRAULIC POWER STEERING, VEHICLES WITH 6-CYLINDER DIESEL ENGINE, VEHICLES WITH AND WITHOUT DYNAMIC STEERING
Clip
Bolt
- 9 Nm
Return Hose
- From the hydraulic oil cooler to the reservoir
- Note location on reservoir. Refer to HOSE LINES TO RESERVOIR, HYDRAULIC FLUID COOLER AND RETURN LINE INSTALLED POSITION .
- Note location on hydraulic oil cooler. Refer to HOSE LINES TO RESERVOIR, HYDRAULIC FLUID COOLER AND RETURN LINE INSTALLED POSITION
Clamp
- Tension using Hose Clip Pliers:VAG1275A
- Always replace if removed
Return Line
- From the power steering gear to the power steering fluid reservoir
  CAUTION:
  - Insert The Return Line Completely When Installing.
- Mounting on the subframe. Refer to COMPONENT LOCATION OVERVIEW - HYDRAULIC POWER STEERING, VEHICLES WITH 6-CYLINDER DIESEL ENGINE, VEHICLES WITH AND WITHOUT DYNAMIC STEERING
Power Steering Gear
- Allocation. Refer to the Parts Information..
- Removing and installing. Refer to STEERING GEAR, REMOVING AND INSTALLING, HYDRAULIC POWER STEERING GEAR .
Seal
- Always replace if removed
Bolt
- 20 Nm
Rubber Bushing
- 9 Nm
Pressure Line
- From the power steering pump to the power steering gear; there are different versions, with and with a separating point. Refer to the Parts Information..
  CAUTION:
  - Insert The Pressure Line Completely When Installing.
- Mounting on crossbrace. Refer to COMPONENT LOCATION OVERVIEW - HYDRAULIC POWER STEERING, VEHICLES WITH 6-CYLINDER DIESEL ENGINE, VEHICLES WITH AND WITHOUT DYNAMIC STEERING
- Wiring connection installation location. Refer to COMPONENT LOCATION OVERVIEW - HYDRAULIC POWER STEERING, VEHICLES WITH 6-CYLINDER DIESEL ENGINE, VEHICLES WITH AND WITHOUT DYNAMIC STEERING
Union Nut
- 40 Nm
- Wiring connection installation location. Refer to COMPONENT LOCATION OVERVIEW - HYDRAULIC POWER STEERING, VEHICLES WITH 6-CYLINDER DIESEL ENGINE, VEHICLES WITH AND WITHOUT DYNAMIC STEERING
- A pressure line with a separating point does not have a union nut.
Nut
- 6 Nm
Bolt
- 25 Nm
Power Steering Pump
- Allocation. Refer to the Parts Information..
- Fill with Hydraulic Fluid before installing
- Delivery pressure, checking. Refer to POWER STEERING PUMP, CHECKING DELIVERY PRESSURE, 6-CYLINDER DIESEL ENGINE, VEHICLES WITH AND WITHOUT DYNAMIC STEERING .
- Removing and installing. Refer to OVERVIEW - POWER STEERING PUMP, VEHICLES WITH 6-CYLINDER DIESEL ENGINE, VEHICLES WITHOUT DYNAMIC STEERING .
Bolt
- 25 Nm
Clamp
- Tension using Hose Clip Pliers:VAG1275A
- Always replace if removed
Intake Hose
- Note location on reservoir. Refer to HOSE LINES TO RESERVOIR, HYDRAULIC FLUID COOLER AND RETURN LINE INSTALLED POSITION .
- Note power steering pump location. Refer to OVERVIEW - POWER STEERING PUMP, VEHICLES WITH 6-CYLINDER DIESEL ENGINE, VEHICLES WITHOUT DYNAMIC STEERING .