Installing (the Camshaft Timing Chain)

WARNING: This page is about a different car, the 2018 Audi Q3 Quattro, 2018 Audi Q3, 2017 Audi Q3 Quattro, and 2017 Audi Q3. However, it is still accessible from the selected car via links, so may be relevant.

Courtesy of AUDI OF AMERICA, LLC

-- Engage the camshaft timing chain with the painted links -arrows- on the camshaft pins.

-- Place the camshaft timing chain on the intake camshaft, exhaust camshaft and the crankshaft. Position the painted chain links -arrows- on the marks on the chain sprockets.

Courtesy of AUDI OF AMERICA, LLC

-- Install the guide rail -2- and tighten the bolts -1-.

Courtesy of AUDI OF AMERICA, LLC

-- Install the upper guide rail -1-.

Courtesy of AUDI OF AMERICA, LLC

The help of a second technician is necessary for the following step.

Courtesy of AUDI OF AMERICA, LLC

I -

Turn the exhaust camshaft using the : T10172A slightly in direction of -arrow A-. Slide the : T40271/1 out of the chain sprocket splines in direction of -arrow B-.

II -

Release the camshaft in the direction -C-, until the timing chain touches the guide rail -1-. Hold the camshaft in this position, install the tensioning rail -2- and tighten the bolts -3-. Release the camshaft.

-- Turn the intake camshaft with the : T40266 in direction of -arrow 1- until the : T40271/2 can be pushed out of the chain sprocket splines -2-. Release the camshaft.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the : T40271/1 and : T40271/2 .

-- Install the bolts -arrows- and tighten them. Tightening specification, refer to -item 4- Bolt (OVERVIEW - CYLINDER HEAD).

Courtesy of AUDI OF AMERICA, LLC

Carefully connect the bearing bracket without tilting - risk of damage.

Courtesy of AUDI OF AMERICA, LLC

-- Mount the bearing bracket and the bolts -arrows- hand-tight.

-- Remove the : T40267 .

Courtesy of AUDI OF AMERICA, LLC

-- Tighten the bearing bracket bolts -arrows-. Tightening specification OVERVIEW - CAMSHAFT TIMING CHAINS .

Courtesy of AUDI OF AMERICA, LLC

-- Install the chain tensioner -2- and tighten the bolt -1-. Remove the : T40011 , the oil pump chain tensioner must come into contact with the cut-out in the oil pan upper section -arrow-.

Courtesy of AUDI OF AMERICA, LLC

-- Check the adjustment. The painted chain links -arrows- must line up with the markings on the chain sprockets.

Courtesy of AUDI OF AMERICA, LLC

-- Install the control valve, refer to -item 7- (OVERVIEW - CAMSHAFT TIMING CHAIN, ENGINE WITH ONE CAMSHAFT ADJUSTER).

-- Let the engine turn a second time in the direction of engine rotation.

NOTE:

Due to the ratio, the painted chain links no longer match up after the engine has been turned.

-- Remove the : T10531/4 and remove the : T10531/3 .

Courtesy of AUDI OF AMERICA, LLC

-- Install the lower timing chain cover. Refer to LOWER TIMING CHAIN COVER, REPLACING .

-- Install the engine support (Cylinder Block, Belt Pulley Side).

-- Install the vacuum pump. Refer to VACUUM SYSTEM .

-- Install the high pressure pump. Refer to HIGH PRESSURE PUMP, REMOVING AND INSTALLING .

-- Install the upper timing chain cover. Refer to TIMING CHAIN COVER, REMOVING AND INSTALLING, ENGINE WITH TWO CAMSHAFT ADJUSTERS .

There are additional procedures depending on the model. Refer to VALVE TIMING, CHECKING and OVERVIEW - VALVETRAIN, ENGINE WITH TWO CAMSHAFT ADJUSTERS . .

-- After performing work on the chain drive the adaptation value in the engine control module must be adapted. To do so, turn on the ignition and select the following menu items on the Vehicle Diagnostic Tester:

01 - Engine Electronics
Guided Functions
01 - Adaptation after repair work on the chain drive