LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2016 >> A6 Premium >> Repair and Diagnosis >> External Pages >> Different car >> Section 67 (Power Tilt & Telescopic Steering Column (Diagnostics - Introduction)) >> Power Tilt And Power Telescopic Steering Column System >> Freeze Frame Data [08/2013 - ] >> Freeze Frame Data [08/2013 - ]

Freeze Frame Data [08/2013 - ]

WARNING: This page is about a different car, the 2014 Lexus ES 300h. However, it is still accessible from the selected car via links, so may be relevant.
  1. FREEZE FRAME DATA 
    NOTE:
    • Freeze frame data values will vary depending on the measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.
    • Turn the power switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the Techstream.
    1. Turn the power switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the power switch on (IG).
    4. Turn the Techstream on.
    5. Check the freeze frame data.
    6. Enter the following menus: Body Electrical / Tilt & Telescopic / Trouble Codes.
      TILT & TELESCOPIC

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Tilt Position Current tilt position data/
      Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Telesco Position Current telescopic position data/
      Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Tilt Return Position Memorized tilt return position data/
      Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Telesco Return Position Memorized telescopic return position data/
      Min.: 0
      Max.: 65535      		 28672 to 36864 -
      Tilt Up Switch Input state of tilt up switch/
      ON or OFF      		 ON: Tilt up switch activated
      OFF: Tilt up switch not activated      		 -
      Tilt Up SW (CAN) Input state of tilt up by switch/
      ON or OFF      		 - (This item is not related to this vehicle)
      Tilt Down Switch Input state of tilt down switch/
      ON or OFF      		 ON: Tilt down switch activated
      OFF: Tilt down switch not activated      		 -
      Tilt Down SW (CAN) Input state of tilt down switch/
      ON or OFF      		 - (This item is not related to this vehicle)
      Telesco Short Switch Input state of telescopic contract switch/
      ON or OFF      		 ON: Telescopic contract switch activated
      OFF: Telescopic contract switch not activated      		 -
      Telesco Short SW (CAN) Input state of telescopic contract switch/
      ON or OFF      		 - (This item is not related to this vehicle)
      Telesco Long Switch Input state of telescopic extend switch/
      ON or OFF      		 ON: Telescopic extend switch activated
      OFF: Telescopic extend switch not activated      		 -
      Telesco Long SW (CAN) Input state of telescopic extend switch/
      ON or OFF      		 - (This item is not related to this vehicle)
      T&T Manual SW Data Voltage data of tilt and telescopic switch/
      Min.: 0.00 V
      Max.: 4.99 V      		 Neutral position: Below 0.20 V
      Tilt up: 1.67 to 2.13 V
      Tilt down: 0.54 to 0.74 V
      Telescopic contract: 1.08 to 1.40 V
      Telescopic extend: 2.22 to 2.77 V      		 -
      Power Source Voltage Voltage data of power supply/
      Min.: 0.00 V
      Max.: 19.99 V      		 11.00 to 14.00 V -
      Freeze Speed Info Vehicle speed data/
      Min.: 0 km/h (0 mph)
      Max.: 255 km/h (158 mph)      		 Actual vehicle speed -
      IG Switch (CAN) Communication state of power switch/
      ON or OFF      		 ON: Communication normal
      OFF: Communication interrupted      		 -
      IG Switch Input state of power switch/
      ON or OFF      		 ON: Input signal normal
      OFF: Input signal interrupted      		 -
      Receive from Meter Communication state of combination meter assembly signal/
      OK or Interpt      		 OK: Communication normal
      Interpt: Communication interrupted      		 -
      Receive from Seat ECU Communication state of position control ECU and switch assembly signal/
      OK or Interpt      		 OK: Communication normal
      Interpt: Communication interrupted      		 -
      Receive from Combi Communication state of combination switch ECU signal/
      OK or Interpt      		 OK: Communication normal
      Interpt: Communication interrupted      		 (This item is not related to this vehicle)
      J/B Communication state of main body ECU (multiplex network body ECU) signal/
      OK or Interpt      		 OK: Communication normal
      Interpt: Communication interrupted      		 -
      Handle Position Steering wheel position signal/
      Away or Return      		 Away: Steering wheel in away position
      Return: Steering wheel in return position      		 -
      The Number of DTCs Number of stored DTCs/
      Min.: 0
      Max.: 255      		 Actual number of stored DTCs -
scientia non olet · About LEMON Manuals