Pinpoint Test J : U0200:87
WARNING: This page is about a different car, the 2018 Lincoln Navigator. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
If new modules were installed prior to the DTC being set, the module configuration may be incorrectly set during the PMI or the PMI may not have been performed.
- J1 CHECK THE COMMUNICATION NETWORK
- Ignition ON.
- Using a diagnostic scan tool, perform a network test.
Does the PDM pass the network test?
Yes GO to J2 No DIAGNOSE no communication with the PDM. REFER to: Communications Network . - J2 CHECK THE BCM (BODY CONTROL MODULE) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)
- Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
- Wait 10 seconds.
- Using a diagnostic scan tool, check the BCM Continuous Memory Diagnostic Trouble Codes (CMDTCs).
Is DTC U3006:16, U3006:17, U3007:16, U3007:17, U3013:16, U3013:17, U3014:16 or U3014:17 recorded?
Yes For DTC U3006:16, U3007:16, U3013:16 or U3014:16, GO to Pinpoint Test K . For DTC U3006:17, U3007:17, U3013:17 or U3014:17, GO to Pinpoint Test L No GO to J3 - J3 RETRIEVE THE DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE PDM (PASSENGER DOOR MODULE)
- Using a diagnostic scan tool, perform the PDM self-test.
Are any Diagnostic Trouble Codes (DTCs) recorded?
Yes REFER to: Locks, Latches and Entry Systems . No GO to J4 - J4 RECHECK THE BCM (BODY CONTROL MODULE) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)
- Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
- Wait 10 seconds.
- Using a diagnostic scan tool, check the BCM Continuous Memory Diagnostic Trouble Codes (CMDTCs).
Is DTC U0200:87 still present?
Yes GO to J5 No The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition. - J5 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U0200:87 SET IN OTHER MODULES
- Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
- Ignition OFF.
- Ignition ON.
- Wait 10 seconds.
- Using a diagnostic scan tool, retrieve all Continuous Memory Diagnostic Trouble Codes (CMDTCs).
Is DTC U0200:87 set in other modules?
Yes GO to J6 No GO to J7 - J6 CHECK FOR CORRECT PDM (PASSENGER DOOR MODULE) OPERATION
- Ignition OFF.
- Disconnect and inspect all PDM electrical connection(s) (harness side connectors and module terminals).
- Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary
- Reconnect all PDM electrical connection(s). Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new PDM. REFER to: Passenger Door Module (PDM) . No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues. - J7 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
- Ignition OFF.
- Disconnect and inspect all BCM electrical connection(s) (harness side connectors and module terminals).
- Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary
- Reconnect all BCM electrical connection(s). Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, BCM guided routine is not applicable for this vehicle and market. Replace the component that was faulted through service information diagnosis. No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.