LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2015 >> A4 Prestige >> Repair and Diagnosis >> External Pages >> Different car >> Section 785 (Supplemental Restraint System) >> Diagnosis And Testing >> Airbag and Safety Belt Pretensioner Supplemental Restraint System (SRS) >> Pinpoint Test >> PINPOINT TEST M : DTCs B1407:11, B1407:12, B1407:13 AND B1407:1A >> PINPOINT TEST M : DTCs B1407:11, B1407:12, B1407:13 AND B1407:1A

PINPOINT TEST M : DTCs B1407:11, B1407:12, B1407:13 AND B1407:1A

WARNING: This page is about a different car, the 2017 Lincoln Navigator and 2017 Ford Expedition. However, it is still accessible from the selected car via links, so may be relevant.
  1. WARNING: Incorrect repair techniques or actions can cause an accidental Supplemental Restraint System (SRS) deployment. Never compromise or depart from these instructions. Failure to precisely follow all instructions could result in serious personal injury from an accidental deployment.
  2. NOTE: Use the correct probe adapter(s) from the Flex Probe Kit when taking measurements. Failure to use the correct probe adapter(s) may damage the connector.
  3. NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
  4. NOTE: Only disconnect or reconnect SRS components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS.
  5. NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, DTCs may set.
  6. NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.

  7. M1 RETRIEVE RCM DTCs

    • WARNING: Before beginning any service procedure, refer to Safety Warnings in Service Information

      REFER to Safety Belt and SRS Health and Safety Precautions in Description and Operation in Service Information .

    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test.

    Was DTC B1407:11, B1407:12, B1407:13 or B1407:1A retrieved on-demand during self-test? 

    Yes  This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test. For DTC B1407:13 or B1407:1A, GO to  M2. For DTC B1407:11, GO to  M8. For DTC B1407:12, GO to  M10.
    No  This is an intermittent fault when present as a CMDTC only. For DTC B1407:13 or B1407:1A, GO to  M13. For DTC B1407:11, GO to  M14. For DTC B1407:12, GO to  M15.

  8. M2 CHECK THE PASSENGER SIDE AIRBAG DEPLOYMENT CONTROL RESISTANCE (DEPLOY_13_R) PID

    • Using a diagnostic scan tool, view RCM PIDs.
    • Monitor and record the resistance value displayed by the DEPLOY_13_R PID.

    Does the PID value read between 1.44 and 3.52 ohms? 

    Yes  GO to  M12.
    No  GO to  M3.

  9. M3 CHECK THE PASSENGER SIDE AIRBAG DEPLOYMENT CONTROL RESISTANCE (DEPLOY_13_R) PID WHILE CARRYING OUT THE HARNESS TEST

    • While monitoring the DEPLOY_13_R PID, carry out the harness test of the passenger side airbag circuits and accessible connectors (including any inline connectors) by wiggling connectors and flexing the wire harness frequently. Record the resistance value indicated by the PID.

    Does the PID value read between 1.44 and 3.52 ohms while carrying out the harness test? 

    Yes  DEPOWER the SRS and REPAIR the connector, terminals or wire harness as needed. Refer to Connector Repair Procedures , for schematic and connector information. Go to  M17.
    No  For PID value less than 1.44 ohms, GO to  M4. For PID value greater than 3.52 ohms, GO to  M6.

  10. M4 CHECK THE PASSENGER SIDE AIRBAG DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (LOW RESISTANCE INDICATED)

    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.

    • Ignition OFF.
    • Disconnect Passenger Side Airbag (Inline) C3052 .
    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test.
    • DIAGNOSTIC TIP:  When viewing DTCs with the passenger side airbag disconnected, an open circuit fault is normally retrieved.

    Did the on-demand DTC change from B1407:1A to B1407:13? 

    Yes  GO to  M11.
    No  GO to  M5.

  11. M5 CHECK FOR A SHORT BETWEEN PASSENGER SIDE AIRBAG CIRCUITS

    • Ignition OFF.
    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C3052-1
      GFD134423Courtesy of FORD MOTOR COMPANY
      		 C3052-2

    Is the resistance greater than 10, 000 ohms? 

    Yes  GO to  M12.
    No  REPAIR the circuits. Refer to Connector Repair Procedures for schematic and connector information. Go to  M17.

  12. M6 CHECK THE PASSENGER SIDE AIRBAG CIRCUITS FOR AN OPEN

    • Ignition OFF.
    • Disconnect Passenger Side Airbag (Inline) C3052 .
    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C310B-37
      GFD134423Courtesy of FORD MOTOR COMPANY
      		 C3052-1
      C310B-38
      GFD134423Courtesy of FORD MOTOR COMPANY
      		 C3052-2

    Are the resistances less than 0.5 ohm? 

    Yes  GO to  M7.
    No  REPAIR the affected circuit. Refer to Connector Repair Procedures for schematic and connector information. Go to  M17.

  13. M7 CHECK THE PASSENGER SIDE AIRBAG DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (OPEN INDICATED)

    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.

    • Connect a fused jumper wire:
      Positive Lead Measurement / Action Negative Lead
      C3052-1
      GFD135987Courtesy of FORD MOTOR COMPANY
      		 C3052-2
    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test.
    • DIAGNOSTIC TIP:  When viewing DTCs with the passenger side airbag circuits shorted together, a low resistance fault is normally retrieved.

    Did the on-demand DTC change from B1407:13 to B1407:1A? 

    Yes  REMOVE the fused jumper wire and GO to  M11.
    No  REMOVE the fused jumper wire and GO to  M12.

  14. M8 CHECK THE PASSENGER SIDE AIRBAG DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (SHORT TO GROUND INDICATED)

    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.

    • Ignition OFF.
    • Disconnect Passenger Side Airbag (Inline) C3052 .
    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test.
    • DIAGNOSTIC TIP:  When viewing DTCs with the passenger side airbag disconnected, an open circuit fault is normally retrieved.

    Did the on-demand DTC change from B1407:11 to B1407:13? 

    Yes  GO to  M11.
    No  GO to  M9.

  15. M9 CHECK THE PASSENGER SIDE AIRBAG CIRCUITS FOR A SHORT TO GROUND

    • Ignition OFF.
    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C3052-1
      GFD134423Courtesy of FORD MOTOR COMPANY
      		 Ground
      C3052-2
      GFD134423Courtesy of FORD MOTOR COMPANY
      		 Ground

    Are the resistances greater than 10, 000 ohms? 

    Yes  GO to  M12.
    No  REPAIR the affected circuit. Refer to Connector Repair Procedures for schematic and connector information. Go to  M17.

  16. M10 CHECK THE PASSENGER SIDE AIRBAG CIRCUITS FOR A SHORT TO VOLTAGE

    • Ignition OFF.
    • Disconnect Passenger Side Airbag (Inline) C3052 .
    • Ignition ON.
    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C3052-1
      GFD134422Courtesy of FORD MOTOR COMPANY
      		 Ground
      C3052-2
      GFD134422Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is any voltage present? 

    Yes  REPAIR the affected circuit. Refer to Connector Repair Procedures for schematic and connector information. Go to  M17.
    No  GO to  M12.

  17. M11 CONFIRM THE PASSENGER SIDE AIRBAG FAULT

    NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out self-test. If not, DTCs will be recorded.

    • Ignition OFF.
    • Prior to reconnecting any previously disconnected SRS component:
      • Inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • Inspect wire harness for any damage, pinched, cut or pierced wires.
      • Inspect RCM C310A and C310B

        CPA lever/lock for correct operation.

      • Inspect Passenger Side Airbag (Inline) C3052 and make sure the CPA tabs are not broken and the clip is not damaged.
    • Connect Passenger Side Airbag (Inline) C3052 .
    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test.

    Was the original DTC retrieved on-demand during self-test? 

    Yes  REMOVE and INSPECT the passenger seat backrest harness for damage. If a concern is found with the passenger seat backrest harness, REPAIR as necessary. Refer to Connector Repair Procedures for schematic and connector information. Go to  M17. If no concern is found with the passenger seat backrest harness, INSTALL a new passenger side airbag. REFER to Side Airbag . GO to  M17.
    No  In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. For DTC B1407:13 or B1407:1A, GO to  M13. For DTC B1407:11, GO to  M14. For DTC B1407:12, GO to  M15.

  18. M12 CONFIRM THE RCM FAULT

    NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.

    • Ignition OFF.
    • Prior to reconnecting any previously disconnected SRS component:
      • Inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • Inspect wire harness for any damage, pinched, cut or pierced wires.
      • Inspect RCM C310A and C310B

        CPA lever/lock for correct operation.

    • Connect Passenger Side Airbag (Inline) C3052 (if previously disconnected).
    • Connect RCM C310A and C310B (if previously disconnected).
    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test.

    Was the original DTC retrieved on-demand during self-test? 

    Yes  CHECK OASIS for any applicable TSBs. If a TSB exists for this concern, discontinue this test and follow TSB instructions. If no TSBs address this concern, INSTALL a new RCM. REFER to Restraints Control Module (RCM) . GO to  M17.
    No  In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. For DTC B1407:13 or B1407:1A, GO to  M13. For DTC B1407:11, GO to  M14. For DTC B1407:12, GO to  M15.

  19. M13 CHECK THE PASSENGER SIDE AIRBAG DEPLOYMENT CONTROL RESISTANCE (DEPLOY_13_R) PID FOR AN INTERMITTENT LOW RESISTANCE OR OPEN CIRCUIT FAULT

    • Using a diagnostic scan tool, view RCM PIDs.
    • While monitoring the DEPLOY_13_R PID, attempt to recreate the fault by wiggling connectors (including any inline connectors) and flexing the wire harness frequently. Record the resistance value indicated by the PID.

    Does the PID value read between 1.44 and 3.52 ohms? 

    Yes  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  M16.
    No  DEPOWER the SRS and REPAIR as necessary. Refer to Connector Repair Procedures , for schematic and connector information. Go to  M17.

  20. M14 CHECK THE PASSENGER SIDE AIRBAG DEPLOYMENT CONTROL FOR AN INTERMITTENT SHORT TO GROUND FAULT

    • Attempt to recreate the fault by wiggling connectors (including any inline connectors) and flexing the wire harness frequently.
    • Using a diagnostic scan tool, perform RCM self-test.

    Was DTC B1407:11 retrieved on-demand during self-test? 

    Yes  DEPOWER the SRS and REPAIR as necessary. Refer to Connector Repair Procedures , for schematic and connector information. Go to  M17.
    No  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  M16.

  21. M15 CHECK THE PASSENGER SIDE AIRBAG DEPLOYMENT CONTROL FOR AN INTERMITTENT SHORT TO BATTERY FAULT

    • Ignition OFF.
    • Disconnect Passenger Side Airbag (Inline) C3052 .
    • Ignition ON.
    • Attempt to recreate the fault by wiggling connectors (including any inline connectors) and flexing the wire harness frequently.
    • Using a diagnostic scan tool, perform RCM self-test.

    Was DTC B1407:12 retrieved on-demand during self-test? 

    Yes  DEPOWER the SRS and REPAIR as necessary. Refer to Connector Repair Procedures , for schematic and connector information. Go to  M17.
    No  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  M16.

  22. M16 CHECK THE HARNESS AND CONNECTORS

    • Ignition OFF.
    • Disconnect Passenger Side Airbag (Inline) C3052 .
      • Inspect connector(s) (including any inline connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
      • Inspect wire harness for any damage, pinched, cut or pierced wires.
      • Inspect RCM C310A and C310B

        CPA lever/lock for correct operation.

      • Inspect Passenger Side Airbag (Inline) C3052

        CPA tab to verify that it is correctly seated and free of damage.

    Were any concerns found? 

    Yes  REPAIR as necessary. Refer to Connector Repair Procedures , for schematic and connector information. Go to  M17.
    No  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  M17.

  23. M17 CHECK FOR ADDITIONAL SRS DTCs

    WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.

    • Ignition OFF.
    • Reconnect all SRS components (if previously disconnected).
    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test.

    Are any RCM DTCs retrieved on-demand during self-test? 

    Yes  Do not clear any DTCs until all DTCs have been resolved. DIAGNOSE and REPAIR the RCM DTCs. REFER to Restraints Control Module (RCM) DTC Chart  for pinpoint test direction.
    No  The repair is complete. RETURN the vehicle to the customer.
scientia non olet · About LEMON Manuals