Luggage Compartment Door Opener does not Operate [08/2013 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / (desired system) / Active Test.
5. Perform the Active Test according to the display on the Techstream.
   BACK DOOR (W/ POWER TRUNK LID SYSTEM)
   
   

   Tester Display	Test Part	Control Range	Diagnostic Note
   Latch Release	Operate luggage door closer assembly latch release	OFF or ON	-

   MAIN BODY (W/O POWER TRUNK LID SYSTEM)
   
   

   Tester Display	Test Part	Control Range	Diagnostic Note
   Trunk and Back-Door Open	Operate luggage compartment door lock assembly latch release	OFF or ON	-

   OK

   Luggage door closer assembly*1 or luggage compartment door lock assembly*2 latch release motor is ON/OFF.

   • *1: w/ Power Trunk Lid System
   • *2: w/o Power Trunk Lid System
   RESULT
   
   

   Result	Proceed to
   OK	A
   NG (w/ Power Trunk Lid System)	B
   NG (w/o Power Trunk Lid System)	C

B → See step   17 

C → See step   11 

A: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Main Body / Data List.
5. Read the Data List according to the display on the Techstream.
   MAIN BODY
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Trunk Lock/Unlock SW	Luggage compartment door lock cylinder assembly switch signal / ON or OFF	ON: Luggage compartment door lock cylinder assembly on (Luggage compartment door opened) OFF: Luggage compartment door lock cylinder assembly off (Luggage compartment door closed)	When this item is abnormal, there is a problem with the luggage compartment door lock cylinder switch assembly or related parts.
   Trunk/BDoor Open SW	Luggage door opening switch assembly signal / ON or OFF	ON: Luggage door opening switch assembly is on OFF: Luggage door opening switch assembly is off	-
   Trunk Main SW	Luggage door opening cancel switch assembly signal / ON or OFF	ON: Luggage door opening cancel switch assembly is on OFF: Luggage door opening cancel switch assembly is off	-
   Luggage courtesy SW	Luggage door closer assembly courtesy switch signal / ON or OFF	ON: Luggage door closer assembly courtesy switch on OFF: Luggage door closer assembly courtesy switch off	For vehicles with power trunk lid system, this item is not related to luggage compartment door condition.

   OK

   On the screen, each item changes between ON and OFF as shown in above chart.

   RESULT
   
   

   Result	Proceed to
   OK	A
   NG (Luggage door opening switch assembly)	B
   NG (Luggage door opening cancel switch assembly)	C
   NG (Luggage compartment door lock cylinder switch assembly)	D
   NG (Luggage courtesy switch)	E

B → See step   5 

C → See step   7 

D → See step   9 

E → See step   21 

A: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Smart Access / Data List.
5. Read the Data List according to the display on the Techstream.
   SMART ACCESS
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Tr/B-Door Unlock SW	Luggage electrical key switch / ON or OFF	ON: Luggage electrical key switch pushed OFF: Luggage electrical key switch not pushed	When this item is abnormal, there is a problem with the luggage electrical key switch of the luggage door closer assembly or related parts.

   OK

   On the screen, each item changes between ON and OFF as shown in above chart.

NG → See step   18 

OK: Go to next step 

1. Temporarily replace the main body ECU (multiplex network body ECU) with a new one. Refer to REMOVAL [08/2013 - ] .
2. Check that the luggage door opener system is normal.

   OK

   Luggage door opener system is normal.

NG → See step   18 

OK → END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE) 

1. Remove the luggage door opening switch assembly. Refer to REMOVAL [08/2013 - ] .
2. Inspect the luggage door opening switch assembly. Refer to INSPECTION [08/2013 - ] .

NG → See step   15 

OK: Go to next step 

1. Disconnect the H9 main body ECU (multiplex network body ECU) connector.
2. Disconnect the H69 luggage door opening switch assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   H9-5 (TSW) - H69-6 (B)	Always	Below 1 Ω
   H69-3 (L) - Body ground	Always	Below 1 Ω
   H9-5 (TSW) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → See step   19 

1. Remove the luggage door opening cancel switch assembly. Refer to REMOVAL [08/2013 - ] .
2. Inspect the luggage door opening cancel switch assembly. Refer to INSPECTION [08/2013 - ] .

NG → See step   16 

OK: Go to next step 

1. Disconnect the H9 main body ECU (multiplex network body ECU) connector.
2. Disconnect the H74 luggage door opening cancel switch assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   H9-11 (TMSW) - H74-2 (B)	Always	Below 1 Ω
   H74-1 (L) - Body ground	Always	Below 1 Ω
   H9-11 (TMSW) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → See step   19 

1. Remove the luggage compartment door lock cylinder assembly. Refer to DISASSEMBLY [08/2013 - ] .

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   1 - 2	Not turned	10 kΩ or higher
   1 - 2	Turned	Below 1 Ω

   TEXT IN ILLUSTRATION
   
   

   *a	Component without harness connected: (Luggage Compartment Door Lock Cylinder Assembly)

NG → See step   20 

OK: Go to next step 

1. Disconnect the H10 main body ECU (multiplex network body ECU) connector.
2. Disconnect the U4 luggage compartment door lock cylinder assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   H10-23 (TKUL) - U4-2 (UL)	Always	Below 1 Ω
   U4-1 (E) - Body ground	Always	Below 1 Ω
   H10-23 (TKUL) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → See step   19 

1. Remove the luggage compartment door lock assembly. Refer to REMOVAL [08/2013 - ] .

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Check the operation of the door lock motor.
   1. Move the door lock to the close (lock) position.
   2. Apply auxiliary battery voltage to the door lock motor and check operation of the door lock motor.

      OK

      Measurement Condition	Specified Condition
      Auxiliary battery positive (+) → Terminal 1 (B) Auxiliary battery negative (-) → Terminal 2 (E)	Luggage compartment door lock motor open (unlock) operation

3. Check the operation of the door courtesy switch.
   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection	Condition	Specified Condition
      3 (D+) - 2 (E)	Fully latched	10 kΩ or higher
      3 (D+) - 2 (E)	Fully open	Below 1 Ω

      TEXT IN ILLUSTRATION
      
      

      *a	Component without harness connected: (Luggage Compartment Door Lock Assembly)
      *b	Close (Lock)
      *c	Open (Unlock)

NG → See step   14 

OK: Go to next step 

1. Disconnect the U3 luggage compartment door lock assembly connector.
2. Disconnect the H10 main body ECU (multiplex network body ECU) connector.
3. Disconnect the 3C instrument panel junction block assembly connector.
4. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   U3-3 (D+) - H10-19 (LGCY)	Always	Below 1 Ω
   U3-1(B) - 3C-10	Always	Below 1 Ω
   3C-10 - Body ground	Always	Below 1 Ω
   U3-2 (E) - Body ground	Always	Below 1 Ω
   U3-3 (D+) - Body ground	Always	10 kΩ or higher
   U3-1 (B) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Temporarily replace the instrument panel junction block assembly with a new or known good one.
2. Check that the luggage door opener system is normal.

   OK

   Luggage door opener system is normal.

NG → See step   19 

OK → END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)