Overview - Headlamp, Halogen Headlamps (Through My 2012)

Observe notes on contact corrosion. Refer to CONTACT CORROSION .

Part 1 

Courtesy of AUDI OF AMERICA, LLC

1. Headlamp Washer System Spray Nozzle
2. Screw
   • Tightening specification. Refer to OVERVIEW - HEADLAMP HOUSING MOUNT, VEHICLES THROUGH MY 2012 .
3. Bracket
   • Overview. Refer to OVERVIEW - HEADLAMP HOUSING MOUNT, VEHICLES THROUGH MY 2012 .
4. Ventilation
   • For the headlamp housing
   • There are different versions.
5. Screw
   • Tightening specification. Refer to OVERVIEW - HEADLAMP HOUSING MOUNT, VEHICLES THROUGH MY 2012 .
6. Screw
   • Tightening specification. Refer to OVERVIEW - HEADLAMP HOUSING MOUNT, VEHICLES THROUGH MY 2012 .
7. Ventilation Hose
   • Overview. Refer to OVERVIEW - HEADLAMP HOUSING MOUNT, VEHICLES THROUGH MY 2012 .
8. Headlamp Housing Bracket
9. Screw
   • 1.8 Nm
10. Screw
    • 4.5 Nm
11. Screw
    • 4.5 Nm
12. Impact Screw
13. Headlamp Housing Bracket
14. Screw
    • 4.5 Nm
15. Spring Nut
16. High Beam Headlamp Bulb
    • Left High Beam Headlamp Bulb -M30-
    • Right High Beam Headlamp Bulb -M32-
    • 12 V, 55 W (H7)
    • Bulb, replacing. Refer to LEFT/RIGHT HIGH BEAM HEADLAMP BULB -M30- / -M32-, REMOVING AND INSTALLING, HALOGEN HEADLAMPS THROUGH MY 2012 .
17. Housing Cover
    • For the high beam headlamps
18. Housing Cover
    • For the low beam headlamps
19. Low Beam Headlamp Bulb
    • Left Low Beam Headlamp Bulb -M29-
    • Right Low Beam Headlamp Bulb -M31-
    • 12 V, 55 W (H7)
    • Bulb, replacing. Refer to LEFT/RIGHT LOW BEAM HEADLAMP BULB -M29- / -M31-, REMOVING AND INSTALLING, HALOGEN HEADLAMPS THROUGH MY 2012 .
20. Headlamp Housing
    • The front side marker lamp bulb is an LED and is integrated in the headlamp housing. The LED cannot be replaced. The entire headlamp must be replaced.
    • Removing and installing. Refer to HEADLAMP, REMOVING AND INSTALLING, HALOGEN HEADLAMPS THROUGH MY 2012 .
21. Screw
    • Tightening specification. Refer to OVERVIEW - HEADLAMP HOUSING MOUNT, VEHICLES THROUGH MY 2012 .
22. Spring Nut
23. Screw
    • Tightening specification. Refer to OVERVIEW - HEADLAMP HOUSING MOUNT, VEHICLES THROUGH MY 2012 .
24. Spring Nut
25. Mount
    • Overview. Refer to OVERVIEW - HEADLAMP HOUSING MOUNT, VEHICLES THROUGH MY 2012 .
26. Screw
    • Tightening specification. Refer to OVERVIEW - HEADLAMP HOUSING MOUNT, VEHICLES THROUGH MY 2012 .
27. Screw
    • Tightening specification. Refer to OVERVIEW - HEADLAMP HOUSING MOUNT, VEHICLES THROUGH MY 2012  .
28. Front Airbag Crash Sensor
    • Removing and installing. Refer to COMPONENT LOCATION OVERVIEW - AIRBAG CRASH SENSORS .

Part 2 - Repair Kits 

Courtesy of AUDI OF AMERICA, LLC

1. Headlamp Housing
   • Removing and installing. Refer to HEADLAMP, REMOVING AND INSTALLING, HALOGEN HEADLAMPS THROUGH MY 2012 .
2. Front Turn Signal Bulb
   • Left Front Turn Signal Bulb -M5-
   • Right Front Turn Signal Bulb -M7-
   • 12 V, 24 W - yellow
   • Bulb, replacing. Refer to LEFT/RIGHT FRONT TURN SIGNAL BULB -M5- / -M7-, REMOVING AND INSTALLING, HALOGEN HEADLAMPS THROUGH MY 2012 .
3. Seal
   • Not available separately as a replacement part
4. Turn Signal Housing Cover
   • The headlamp housing must be cut open to replace the bulb.
   • A housing cover can be ordered to seal the assembly opening.
   • Removing and installing. Refer to LEFT/RIGHT FRONT TURN SIGNAL BULB -M5- / -M7-, REMOVING AND INSTALLING, HALOGEN HEADLAMPS THROUGH MY 2012 .
5. Screw
   • 2 Nm
   • From the turn signal cover repair set
6. Headlamp Beam Adjustment Motor
   • Left Headlamp Beam Adjustment Motor -V48- : removing and installing. Refer to Left Headlamp Beam Adjustment Motor -V48-, REMOVING AND INSTALLING, HALOGEN HEADLAMPS THROUGH MY 2012 .
   • Right Headlamp Beam Adjustment Motor -V49- ; not available separately as a replacement part
7. Seal
   • Not available separately as a replacement part
8. Headlamp Beam Adjustment Motor Housing Cover
   • Only for the left headlamp
   • The headlamp housing must be cut open to replace the adjustment motor
   • A housing cover can be ordered to seal the assembly opening.
   • Removing and installing. Refer to Left Headlamp Beam Adjustment Motor -V48-, REMOVING AND INSTALLING, HALOGEN HEADLAMPS THROUGH MY 2012 .
9. Screw
   • 2 Nm
   • From the repair kit for the headlamp range control adjustment motor cover
10. Screw
    • 1.4 Nm
11. Position Lamp/Daytime Running Lamp Housing Cover
    • The headlamp housing must be cut open to replace the bulb.
    • A housing cover can be ordered to seal the assembly opening.
    • Removing and installing. Refer to LEFT/RIGHT POSITION LAMP BULB -M1- / -M3-, REMOVING AND INSTALLING, HALOGEN HEADLAMPS THROUGH MY 2012 .
12. Daytime Running Lamp Bulb
    • Left Daytime Running Lamp Bulb -L174-
    • Right Daytime Running Lamp Bulb -L175-
    • 12 V, 13 W
    • Bulb, replacing. Refer to LEFT/RIGHT DAYTIME RUNNING LAMP BULB -L174- / -L175-, REMOVING AND INSTALLING, HALOGEN HEADLAMPS THROUGH MY 2012 .
13. Position Lamp Bulb/Daytime Running Lamp
    • Left Position Lamp Bulb -M1-
    • Right Position Lamp Bulb -M3-
    • With daytime running lamp function
    • Position lamp dimmed 70%
    • 12 V, 13 W
    • Bulb, replacing. Refer to LEFT/RIGHT POSITION LAMP BULB -M1- / -M3-, REMOVING AND INSTALLING, HALOGEN HEADLAMPS THROUGH MY 2012 .
14. Position Lamp/Daytime Running Lamp Housing Cover
    • The headlamp housing must be cut open to replace the bulb.
    • A housing cover can be ordered to seal the assembly opening.
    • Removing and installing. Refer to LEFT/RIGHT DAYTIME RUNNING LAMP BULB -L174- / -L175-, REMOVING AND INSTALLING, HALOGEN HEADLAMPS THROUGH MY 2012 .