Mounting Bracket, Manual Transmission: Removing

WARNING: This page does not describe the selected car, but rather 23 other vehicles, including the 2017 Audi S5, 2017 Audi A5 Quattro, 2016 Audi S5, 2016 Audi A5 Quattro, and 2015 Audi S5. However, it is still accessible from the selected car via links, so may be relevant.

WARNING:

Lay clean cloths in the footwell to protect against brake fluid leaking from the clutch pedal.

-- Remove the driver side instrument panel cover -1 to 3-.

Fig 1: Identifying Driver Side Storage Compartment

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the connector -C- on the footwell vent.

Fig 2: Identifying Footwell Vents

Courtesy of AUDI OF AMERICA, LLC

-- Remove the footwell vents -A-B-.

-- Remove the brake lamp sensor, refer to BRAKE LAMP SENSOR .

-- Disconnect the connector from the accelerator pedal module.

-- Separate the brake pedal from the brake booster, refer to BRAKE PEDAL AND BRAKE BOOSTER, DISCONNECTING AND CONNECTING .

WARNING:

If possible, leave the brake pedal stop installed; it could break the mount for the brake lamp sensor if the brake pedal is released too quickly.

-- Remove the over-center spring -2- on the clutch pedal -1- .

Fig 3: Actuating Clutch Pedal

Courtesy of AUDI OF AMERICA, LLC

NOTE:

When re-installing later, make sure the over-center spring is installed correctly.

-- Remove the pins in the clutch pedal -4- to the clutch master cylinder from the pedal arm -3-.

Fig 4: Identifying Mounting Pins

Courtesy of AUDI OF AMERICA, LLC

NOTE:

Unlatch the lock -1 and 2 - only when it is removed.

-- Release the clutch master cylinder 3355.

Rotate the tool clockwise -arrow-.

Fig 5: Rotating Tool 3335 Clockwise -Arrow- To Remove Tower Brace

Courtesy of AUDI OF AMERICA, LLC

-- Remove the tower brace.

-- Remove the plenum chamber bulkhead, refer to OVERVIEW - BULKHEAD .

-- Remove the cover -2- over the brake fluid reservoir.

Fig 6: Identifying Brake Master Cylinder Components

Courtesy of AUDI OF AMERICA, LLC

The cover -2- is not installed on all vehicle models.

-- Remove the bolts mounting the brake booster -1- to the mounting bracket.

Fig 7: Identifying Brake Booster Bolts, Brake Lines & Brake Master Cylinder Bolts

Courtesy of AUDI OF AMERICA, LLC

-- Remove the nuts -16- on the mounting bracket guides.

Fig 8: Identifying Brake Pedal Assembly Overview

Courtesy of AUDI OF AMERICA, LLC

-- Turn the steering wheel with the steering wheel adjustment as far as possible to the rear, toward the driver seat.

-- Move the steering wheel into the straight-ahead position The vehicle wheels are in the straight-ahead position as well.

NOTE:

It is not necessary to remove the instrument cluster and steering in order to remove the steering column.

-- Remove the lower bolts -2- on the steering column.

Fig 9: Identifying Steering Intermediate Shaft

Courtesy of AUDI OF AMERICA, LLC

-- Remove the lower bolts -2 through 4- for the steering column and mounting bracket.

Fig 10: Identifying Lower Steering Column Bolts

Courtesy of AUDI OF AMERICA, LLC

-- Unclip the gap cover -2- from the upper trim -1- for the steering column switch module -arrow A-.

Fig 11: Using Small Flat-Head Screwdriver To Unclip Gap Cover From Upper Steering Column Switch Module Trim

Courtesy of AUDI OF AMERICA, LLC

-- Remove the cable guides on the steering column.

NOTE:

The steering wheel is not shown in the illustration. It is not necessary to remove the steering wheel and instrument cluster.

-- Remove the steering column bolts -1 and 2- on the central tube while supporting the steering column from below with the hand.

Fig 12: Identifying Steering Column Bolts

Courtesy of AUDI OF AMERICA, LLC

NOTE:

Loosen and remove the bolts -1 and 2- with a pawl with a 3/8" drive and socket and extension.

-- Pull the steering column out of the steering shaft.

-- Carefully lay down the steering column and steering wheel.

-- Remove the mounting bracket from the vehicle.

CAUTION:

When removing the mounting bracket, be careful not to pull the clutch master cylinder out of the hydraulic line.

The clutch master cylinder remains in the vehicle.