Diagnostic Mode 02 - Read Operating Conditions
When an emissions-related fault (pending DTC, visible in mode 07) is first detected, operating conditions are stored. Mode 02 makes it possible to access this freeze frame data as soon as this fault is shown in mode 03. Each control module only shows freeze frame data for one fault via mode 02. Therefore, there are two priority levels. If there is a malfunction with higher priority, the freeze frame data is overwritten.
-- Fault with higher priority: Misfire malfunction or fuel trim malfunction.
-- Fault with normal priority: All other emissions-related faults.
Depending on scan tool and protocol used, the information in diagnostic mode 02 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).
Procedure
-- Connect the scan tool.
-- Start the engine and run at idle.
If the engine does not start, crank the engine using starter for at least 5 seconds, do not switch the ignition off afterward under any circumstances.
-- Select "Diagnostic Mode 2: Obtain operating conditions.".
-- From the following table, select the desired the "PID", e.g. "PID 05-Coolant temperature" that is to be monitored.
The current values of the component or system that is being monitored will be displayed on the scan tool screen.
| PID | Component or System |
|---|---|
| $00: | Supported Definition PIDs, $01 thru $20 |
| $02: | Fault Code That Caused The Freeze Frame To Be Stored |
| $03: | Fuel System Status |
| $04: | Calculated Load Value |
| $05: | Coolant Temperature |
| $06: | Short Term Air Fuel Ratio |
| $07: | Long Term Air Fuel Ratio |
| $08: | Short Term Air Fuel Ratio Bank 2 |
| $09: | Long Term Air Fuel Ratio Bank 2 |
| $0C: | Engine RPM |
| $0D: | Vehicle Speed |
| $0E: | Ignition Timing Advance For #1 Cylinder |
| $11: | Throttle Valve Position 1 Absolute (Throttle Valve Position 1) |
| $12: | Secondary Air Injection |
| $1F: | Time After Engine Start |
| $20: | Supported Definition PIDs, $21 Thru $40 |
| $23: | Fuel Pressure (Rail Pressure) |
| $2E: | Activation Of Tank Vent Valve |
| $2F | Tank Level |
| $33: | Ambient Pressure |
| $40: | Supported Definition PIDs, $41 thru $60 |
| $42: | Control Modules System Voltage |
| $43: | Absolute Load Value |
| $44: | Oxygen Sensor Specified Value |
| $45: | Relative Throttle Position |
| $46: | Ambient Air Temperature |
| $47: | Throttle Valve Position 2 Absolute (Throttle valve position 2) |
| $49: | Accelerator Pedal Position 1 Absolute (Accelerator Pedal Position Signal 1) |
| $4A: | Accelerator Pedal Position 2 Absolute (Accelerator Pedal Position Signal 2) |
| $4C: | Specified Throttle Valve Position |
| $51 | Fuel Type |
| $56: | Offset Oxygen Sensor Regulation After Catalytic Converter Bank 1 |
| $58: | Offset Oxygen Sensor Regulation After Catalytic Converter Bank 2 |
| $60: | Supported Definition PIDs $61 thru $80 |
| $67 | Engine Coolant Temperature 2 |
| $68: | Intake Air Temp. (IAT) Bank 1 Sensor 1 |
| $6F: | Turbocharger Compressor Inlet Press. Sensor A |
| $70: | Boost Pressure Sensor A Boost Pressure Sensor B |
| $77: | Charger Air Cooler Temperature (CACT) Bank 1 Sensor 1 Bank 2 Sensor 1 |
-- Switch the ignition off.