Outside Air Temperature Sensor -G17-, Checking
WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2017 Audi S5, 2016 Audi S5, 2016 Audi S4, 2015 Audi S5, and 2015 Audi S4. However, it is still accessible from the selected car via links, so may be relevant.
General Description
The ambient or Outside Air Temperature Sensor -G17- is a negative temperature coefficient (NTC) sensor that informs the semiautomatic / automatic temperature control system of outside air temperature. An NTC sensor resistance decreases as the temperature increases. The computer uses this input along with different in-car temperature sensors to control temperature and blower speed. When there is a problem with this sensor, performance will suffer and the compressor clutch may not engage.
Special tools and workshop equipment required
- Multimeter.
- Wiring Diagram.
- Scan Tool.
Test requirements
- Fuses OK.
- Battery voltage OK.
- Switch OFF all electrical and electronic accessories.
- Vehicles with Auto. Transmission, ensure Selector Lever position is in "P".
- Vehicles with Man. Transmission, ensure Shifter Lever position is in "N" with Parking Brake applied.
- Coolant Temperature: ≥ 80° C.
- Observe all safety precautions: SAFETY PRECAUTIONS
.
- View clean working conditions: CLEAN WORKING CONDITIONS
.
- For Hybrid vehicles refer to: HIGH VOLTAGE SYSTEM GENERAL WARNINGS
.
Test Procedure
| Step |
Procedure |
Result / Action to Take |
| 1 |
- PERFORM: Preliminary Check to verify the customers complaint. Refer to PRELIMINARY CHECK
.
-- Was Complaint verified? |
-- YES:
-- NO:
- GATHER more information from customer about the complaint.
|
| 2 |
- IGNITION: OFF.
- DISCONNECT: Outside Air Temperature Sensor -G17- harness connector.
- CHECK: Outside Air Temperature Sensor -G17- component connector terminals 1 to 2 for resistance.
- SPECIFIED VALUE: 1, 300 Ω (+/- 500 Ω @ approx. 20° C).
-- Was Value obtained? |
-- YES:
-- NO:
- REPLACE: Outside Air Temperature Sensor -G17-. Refer to appropriate repair information.
- GO TO: Step 4
|
| 3 |
- REMOVE: Vehicle Electrical System Control Module -J519-. Refer to appropriate repair information.
- CHECK: Outside Air Temperature Sensor -G17- harness connector terminal 1 to the Vehicle Electrical System Control Module -J519- harness connector T32a / 25 for resistance.
- CHECK: Outside Air Temperature Sensor -G17- harness connector terminal 2 to the Vehicle Electrical System Control Module -J519- harness connector T32a / 10 for resistance.
- SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω).
-- Were Values obtained? |
-- YES:
-- NO:
- CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
- REPAIR: Faulty wiring or connector.
- GO TO: Step 4
|
| 4 |
- Final Procedure
- Perform a road test to verify repair.
-- Does the original DTC return? |
-- YES:
- CHECK: Vehicle Electrical System Control Module -J519- harness connector for any damaged, pushed-out pins.
- REPAIR: As necessary.
- Clear the DTC's. Refer to DIAGNOSTIC MODE 04 - ERASE DTC MEMORY
.
- Repair is complete. Generate Readiness Code. Refer to READINESS CODE
.
- Return vehicle to Customer.
- If all electrical connections are OK:
- REPLACE Vehicle Electrical System Control Module -J519-. Refer to appropriate repair information.
- Repair is complete. Generate Readiness Code. Refer to READINESS CODE
.
- Return vehicle to Customer.
-- NO:
- Perform the diagnostic procedure for any DTC's.
- If no DTC's return the repair is complete.
- Return vehicle to customer.
|