Upper Transverse Link, Tie Rod, Coil Spring, Lower Control Arm And Level Control System Sensor Overview
WARNING: This page does not describe the selected car, but rather 23 other vehicles, including the 2017 Audi S5, 2017 Audi A5 Quattro, 2016 Audi S5, 2016 Audi A5 Quattro, and 2015 Audi S5. However, it is still accessible from the selected car via links, so may be relevant.
- Bolt
- 70 Nm + 180° turn
- Always Replace If Removed.
- Must be tightened in the curb weight position. Refer To WHEEL BEARING WITH COIL SPRING, LIFTING TO CURB WEIGHT POSITION .
- Securing Clip
- Left Rear Level Control System Sensor -G76-
- Only sensors of the same version may be installed.
- Complete with components.
- The sensor lever points toward the outside.
- Replace in vehicle. Refer To LEVEL CONTROL SYSTEM SENSOR .
- After Loosening, Check Basic Setting Of Headlamp Adjustment. Refer To HEADLAMP, ADJUSTING .
- If the sensor was removed and installed on a vehicle with electronically controlled damping or if the linkage was loosened, the control position must be reprogrammed. Refer To CONTROL POSITION, PROGRAMMING USING VEHICLE DIAGNOSTIC TESTER .
- If the control position was reprogrammed on vehicles with lane assist, the directional stabilization assistance control module -J759- must be recalibrated. Refer To LANE ASSIST CALIBRATION PROCEDURE .
- Subframe
- Bolt
- 70 Nm + 180° turn
- Always Replace If Removed.
- Must be tightened in the curb weight position. Refer To WHEEL BEARING WITH COIL SPRING, LIFTING TO CURB WEIGHT POSITION .
- Upper Transverse Link
- Removing and installing, Refer To UPPER TRANSVERSE LINK .
- Nut
- Always Replace If Removed.
- Shim
- Nut
- 95 Nm
- Always Replace If Removed.
- Must be tightened in the curb weight position. Refer To WHEEL BEARING WITH COIL SPRING, LIFTING TO CURB WEIGHT POSITION .
- Adjustment Bolt
- Lower Transverse Link
- Removing and installing, Refer To LOWER TRANSVERSE LINK .
- Bolt
- 120 Nm + 360° turn
- Always Replace If Removed.
- Must be tightened in the curb weight position. Refer To WHEEL BEARING WITH COIL SPRING, LIFTING TO CURB WEIGHT POSITION .NOTE:
Wheel alignment is necessary if the bolt is removed.
- Upper Spring Seat Spacer Washer
- Upper Spring Support
- Installed only on heavy duty suspension and Sportback.
- Coil Spring
- Note different types of suspension versions, see vehicle data plate. Refer To PRODUCTION CONTROL NUMBER (PR NUMBER) EXPLANATIONS .
- Removing and installing, Refer To COIL SPRING .
- Lower Spring Support
- Coil Spring Stone Deflector
- Wheel Bearing Housing
- Spacer Tube
- Always Replace If Removed.
- Nut
- Always Replace If Removed.CAUTION:
- Do not tighten the threaded connection using the nut.
NOTE:Wheel alignment is necessary if the nut is loosened.
- Always Replace If Removed.
- Bolt
- 90 Nm + 90° turn
- Always Replace If Removed.
- Must be tightened in the curb weight position. Refer To WHEEL BEARING WITH COIL SPRING, LIFTING TO CURB WEIGHT POSITION .
- Tie Rod
- Removing and installing, Refer To TIE ROD .
- Note the installation position.
- There are versions made of aluminum and steel. For allocation, Refer To the Parts Information..
- A mixed installation is not permitted.
- Bolt
- Eccentric Washer
- Nut
- 95 Nm
- Always Replace If Removed.
- Must be tightened in the curb weight position. Refer To WHEEL BEARING WITH COIL SPRING, LIFTING TO CURB WEIGHT POSITION .
- Bolt
- 70 Nm + 180° turn
- Always Replace If Removed.
- Must be tightened in the curb weight position. Refer To WHEEL BEARING WITH COIL SPRING, LIFTING TO CURB WEIGHT POSITION .
- Nut
- Always Replace If Removed.
- Bolt
- 9 Nm
- Bolt
- 5 Nm