Drive Axle Overview, With 100 Mm Diameter Outer CV Joint And 108 Mm Diameter Inner CV Joint: Notes

WARNING: This page does not describe the selected car, but rather 23 other vehicles, including the 2017 Audi S5, 2017 Audi A5 Quattro, 2016 Audi S5, 2016 Audi A5 Quattro, and 2015 Audi S5. However, it is still accessible from the selected car via links, so may be relevant.

Fig 1: Drive Axle Overview, With 100 Mm Diameter Outer CV Joint And 108 Mm Diameter Inner CV Joint

Courtesy of AUDI OF AMERICA, LLC

Cover
- Drive the cover off carefully using a drift
- Always replace.
- The adhesive surfaces on the cover/inner CV joint must be free of grease when installing.
- Before mounting on the CV joint, coat the sealing surface with sealant. Refer To INNER CV JOINT, 100 MM DIAMETER OR 108 MM DIAMETER .
Securing Ring
- Remove and install with commercially-available circlip pliers.
- Always replace.
Inner CV joint
- Exterior diameter: 108 mm
- Replace only as complete unit.
- Checking, Refer To INNER CV JOINT, CHECKING .
- Pressing off, Refer To INNER CV JOINT, 100 MM DIAMETER OR 108 MM DIAMETER .
- Pressing on, Refer To INNER CV JOINT, 100 MM DIAMETER OR 108 MM DIAMETER .
- Grease quantity and type, Refer To DRIVE AXLE OVERVIEW, WITH 100 MM DIAMETER OUTER CV JOINT AND 108 MM DIAMETER INNER CV JOINT .
- Adhesive surface must be free of oil and grease.
- When installing joint on axle shaft, splines on axle shaft must be lightly coated with grease used in joint.
Backing Plate
Bolt
- 70 Nm
- Always Replace If Removed.
Clamp
- Always replace.
- Tensioning, Refer To INNER CV JOINT, 100 MM DIAMETER OR 108 MM DIAMETER .
Inner CV Joint Protective Boot
- Without ventilation bore.
- In case of damage, check inner CV joint. Refer To INNER CV JOINT, CHECKING .
- The protective boot/drive shaft sealing surfaces must be free of grease when installing.
- Before tightening clamp, briefly raise CV boot to allow pressure to equalize.
Clamp
- Always replace.
- Tensioning, Refer To INNER CV JOINT, 100 MM DIAMETER OR 108 MM DIAMETER .
Drive Axle
- Removing and installing, Refer To DRIVE AXLE .
CV Boot for Outer CV Joint
- Without ventilation bore.
- Check for tears and chafing; replace if necessary.
- In case of damage, check outer CV joint. Refer To OUTER CV JOINT, CHECKING .
- The protective boot/outer CV joint sealing surfaces must be free of grease when installing.
- Before tightening clamp, briefly raise CV boot to allow pressure to equalize.
Clamp
- Opening, Refer To Removing .
- Tensioning, Refer To Installing .
Securing Ring
- Always replace.
- Allocation Parts Information..
- Insert into ring groove of shaft before installation (not visible on installed joint).
- Before installing CV joint, align the sealing ring in center with opening facing upward.
Outer CV Joint
- Exterior diameter: 100 mm.
- Replace only as complete unit.
- Checking, Refer To OUTER CV JOINT, CHECKING .
- Driving off, Refer To OUTER CV JOINT, 88 MM DIAMETER OR 100 MM DIAMETER .
- Installing: Drive onto shaft using plastic hammer until compressed circlip seats.
- Circlip must lie in joint chamfer when guiding in, guide with pliers if necessary.
- Grease quantity and type. Refer To DRIVE AXLE OVERVIEW, WITH 100 MM DIAMETER OUTER CV JOINT AND 108 MM DIAMETER INNER CV JOINT .
- The protective boot/outer CV joint sealing surfaces must be free of grease when installing.
- When installing joint on axle shaft, splines on axle shaft must be lightly coated with grease used in joint.
Bolt
- Always replace.
- Follow the assembly information when loosening and tightening. Refer To THREADED CONNECTION BETWEEN DRIVE AXLE AND WHEEL HUB, LOOSENING AND TIGHTENING .
- 200 Nm + 180° turn