Track Control Arm, Ball Joint, Guide Link And Level Control System Sensor Overview: Notes
WARNING: This page does not describe the selected car, but rather 23 other vehicles, including the 2017 Audi S5, 2017 Audi A5 Quattro, 2016 Audi S5, 2016 Audi A5 Quattro, and 2015 Audi S5. However, it is still accessible from the selected car via links, so may be relevant.
- Bolt
- Always replace if removed.
- Guide Link
- Removing and installing, refer to GUIDE LINK .
- There are conventional and hydraulic bonded rubber bushings. For the correct allocation, refer to the Parts Information..
- A mixed installation is not permitted.
- 65 mm conventional rubber bonded bushing for guide link, replacing, refer to GUIDE LINK CONVENTIONAL BONDED RUBBER BUSHING, 65 MM .
- Replacing the hydraulic bonded rubber bushing 75 mm for the guide link, refer to GUIDE LINK HYDRAULIC BONDED RUBBER BUSHING, 75 MM .
- Nut
- 70 Nm + 180° turn
- Always replace if removed.
- Must be tightened in the curb weight position. Refer to WHEEL BEARING WITH COIL SPRING, LIFTING TO CURB WEIGHT POSITION .
- Wheel Bearing Housing
- Bolt
- 40 Nm
- Always replace if removed.
- Nut
- Always replace if removed.
- Different versions, for allocation refer to the Parts Information..
- Pay attention to the different nut versions and to the tightening specifications. Refer to TRACK CONTROL ARM, BALL JOINT, GUIDE LINK AND LEVEL CONTROL SYSTEM SENSOR OVERVIEW .
- After loosening threaded connection of guide control arm to wheel bearing housing, adhesive residue must be removed on thread of linkage stub.
- Ball Joint
- Removing and installing, refer to BALL JOINT .
- Different versions. Allocation, refer to the Parts Information..NOTE:
Note installation position. Refer to Installing .
Install the ball joint into the wheel bearing housing as far as the contact surface.
- Nut
- Always replace if removed
- Different versions. Allocation, refer to the Parts Information..
- Pay attention to the different nut versions and to the tightening specifications. Refer to TRACK CONTROL ARM, BALL JOINT, GUIDE LINK AND LEVEL CONTROL SYSTEM SENSOR OVERVIEW .
- After loosening threaded connection on the ball joint to the wheel bearing housing, adhesive residue must be removed on thread of linkage stub.
- Nut
- 90 Nm + 90° turn
- Always replace if removed.
- Must be tightened in the curb weight position. Refer to WHEEL BEARING WITH COIL SPRING, LIFTING TO CURB WEIGHT POSITION .
- Control Arm
- Removing and installing, refer to TRACK CONTROL ARM .
- Different versions. Allocation, refer to the Parts Information..
- Replacing bearings for track control arm. Refer to TRACK CONTROL ARM BALL BEARING .
- Bolt
- Always replace if removed.
- Nut
- 9 Nm
- Bolt
- Always replace if removed.
- Nut
- 70 Nm + 180° turn
- Always replace if removed.
- Must be tightened in the curb weight position. Refer to WHEEL BEARING WITH COIL SPRING, LIFTING TO CURB WEIGHT POSITION .
- Left Front Level Control System Sensor -G78- or Right Front Level Control System Sensor -G289-
- Install an identical sensor.
- Only remove and install or replace completely. Refer to LEVEL CONTROL SYSTEM SENSOR .
- The sensor lever must point toward the back.
- Adjust the headlamp after loosening. Refer to appropriate service information. .
- If the sensor was removed and installed on a vehicle with electronically controlled damping or if the linkage was loosened, the control position must be reprogrammed. Refer to CONTROL POSITION, PROGRAMMING USING VEHICLE DIAGNOSTIC TESTER .
- If the control position was reprogrammed on vehicles with lane assist, the directional stabilization assistance control module -J759- must be recalibrated. Refer to LANE ASSIST CALIBRATION PROCEDURE .
- Bolt
- 20 Nm
- Shock Absorber Fork