Valve Stem Seals With Cylinder Hear Removed, Replacing

Special tools and workshop equipment required 

• Puller - Valve Seal 3364
• Seal Installer - Valve Stem 3365
• Valve Cotter Tool Kit VAS5161A with Valve Cotter Tool Kit - Guide Plate 19C VAS5161/19C
• Engine and Gearbox Bracket VAS6095A VAS6095A
• Cylinder Head Tensioning Device VAS6419

Procedure 

-- Remove the camshafts. Refer to CAMSHAFT, REMOVING AND INSTALLING .

-- Mark the allocation of the roller rocker lever and the hydraulic adjusting elements so they can be installed again.

-- If necessary, remove the roller rocker levers with the hydraulic adjusting elements and place them on a clean surface.

-- Insert the Cylinder Head Tensioning Device VAS6419 in the Engine and Gearbox Bracket VAS6095A.

Fig 1: Tensioning Cylinder Head On Tensioning Element VAS 6419

Courtesy of AUDI OF AMERICA, LLC

-- Tension the cylinder head on the cylinder head tensioning device, as illustrated.

-- Connect the cylinder head tensioning device to the compressed air.

-- Slide the air cushion with the lever -arrow- under the combustion chambers onto the valve stem seal that will be removed.

-- Let enough compressed air flow into the air cushion until it contacts the valve plate.

-- Position the Valve Cotter Tool Kit - Punch VAS5161/3A on the valve spring plate and loosen the stuck valve retainers with a plastic mallet.

Fig 2: Identifying Valve Cotter Tool Kit - Punch VAS 5161/3

Courtesy of AUDI OF AMERICA, LLC

-- Place Valve Cotter Tool Kit - Guide Plate VAS5161/19C from Valve Cotter Tool Kit VAS5161 on the cylinder head.

Fig 3: Placing Valve Cotter Tool Kit - Guide Plate 19C VAS 5161/19C On Cylinder Head

Courtesy of AUDI OF AMERICA, LLC

-- Secure the guide plate with the Valve Cotter Tool Kit - Knurled Thumb Screws VAS5161/12.

-- Install the Valve Cotter Tool Kit - Retainer VAS5161/6 with the Valve Cotter Tool Kit - Guide Forks M6/M8 with Threaded Studs VAS5161/5 in the guide plate.

Fig 4: Identifying Valve Cotter Tool Kit - Guide Plate 19c VAS5161/19C

Courtesy of AUDI OF AMERICA, LLC

-- Push the Valve Cotter Tool Kit - Assembly Cartridge VAS5161/8A into guide plate.

-- Engage the Valve Cotter Tool Kit - Pressure Fork VAS5161/2 at the engaging device and press the installation cartridge downward.

-- At the same time, rotate the cartridge knurled screw right until points engage in valve retainers.

-- Move the knurled wheel left and right slightly. This presses the valve retainers apart and captures them in the cartridge.

-- Release the pressure fork.

-- Remove the cartridge.

-- Unfasten guide plate and turn it aside.

-- Remove the valve spring and the valve spring plate.

-- Remove the valve stem seal with the Puller - Valve Seal 3364.

Fig 5: Identifying 3364

Courtesy of AUDI OF AMERICA, LLC

Fig 6: Identifying Plastic Sleeve And Valve Stem Seals

Courtesy of AUDI OF AMERICA, LLC

-- Lightly oil the valve stem seal.

-- Slide the valve stem seal onto the plastic sleeve.

-- Carefully press the valve stem seal onto the valve guide with the Seal Installer - Valve Stem 3365.

-- Remove plastic sleeve.

If the valve retainers were removed from the installation cartridge, they must be inserted into the Valve Cotter Tool Kit - Valve Insertion Device VAS5161/18 first.

Fig 7: Identifying Installation Cartridge VAS 5161/8

Courtesy of AUDI OF AMERICA, LLC

• The large diameter of the valve retainers point upward.

-- Press assembly cartridge from above onto valve insertion device and capture retainers.

-- Insert valve spring and valve spring plate.

• Installed position, valve spring. Refer to Figure.

-- Attach the Valve Cotter Tool Kit - Guide Plate 19C VAS5161/19C onto the cylinder head again.

Fig 8: Identifying Valve Cotter Tool Kit - Guide Plate 19c VAS5161/19C

Courtesy of AUDI OF AMERICA, LLC

-- Insert installation cartridge in guide plate.

-- Press the pressure fork down and pull the knurled screw up while turning left and right. This inserts the valve retainers.

-- Release the pressure fork with the knurled screw still raised.

-- Repeat the procedure on each valve.

Assembling 

Assemble in reverse order of disassembling. Note the following:

-- Make sure all the roller rocker levers lie on the ends of the valve stems correctly and are clipped onto the respective hydraulic adjusting elements.

-- Install the camshafts. Refer to CAMSHAFT, REMOVING AND INSTALLING .