Driveshaft, Removing And Installing, Driveshaft Connected On Transmission Side: Removing

WARNING: This page does not describe the selected car, but rather 13 other vehicles, including the 2017 Audi SQ5, 2017 Audi Q5, 2016 Audi SQ5, 2016 Audi Q5, and 2015 Audi SQ5. However, it is still accessible from the selected car via links, so may be relevant.

NOTE:

The attached driveshaft can only be separated from the transmission if it is completely removed.

Perform work on driveshaft on a two-column shop hoist if possible.

After removing the driveshaft from the rear final drive, tie up the shaft ends or hold them up.

The driveshaft can be bent all the way to the center joint without force. Bending the joint forcibly all the way can damage the center joint and/or the protective boot.

Always remove or install the driveshaft horizontally from the transmission output shaft.

CAUTION:

Risk of damaging the coupling elements.

Do not bend the coupling more than 10°.
Do not load the coupling.
Do not damage the wire mesh on the coupling.

Vehicles with 3.0L TDI driveshaft and Two Turbochargers .

Fig 1: Removing/Installing Particulate Filter Or SCR Catalytic Converter

Courtesy of AUDI OF AMERICA, LLC

-- Remove the particulate filter or SCR catalytic converter. Refer to SCR CATALYTIC CONVERTER, REMOVING AND INSTALLING .

Continuation for Driveshaft

Fig 2: Clamping Sleeve Threaded Connections

Courtesy of AUDI OF AMERICA, LLC

-- Loosen clamping sleeve(s) -arrows- and push it toward the rear.

-- Tie the front muffler or the left and right front exhaust pipe to the underbody.

-- Remove the bolts -arrows- and remove the driveshaft heat shield -1- (if equipped).

Fig 3: Driveshaft Heat Shield - Tightening Specification

Courtesy of AUDI OF AMERICA, LLC

-- Cut the clamp -1- for the driveshaft boot and remove it.

Fig 4: Driveshaft Boot Hose Clamp

Courtesy of AUDI OF AMERICA, LLC

NOTE:

Ignore item -2-.

Audi A6 and A7

Fig 5: Identifying Crossbrace (Audi A6 and A7)

Courtesy of AUDI OF AMERICA, LLC

-- Remove the crossmember -2-. Refer to Underbody Panel .

Audi A4, A5 Coupe, A5 Sportback, A5 Cabrio, Q5, A8

Fig 6: Identifying Crossmember (A4, A5 Coupe/Sportback/Cabrio, Q5)

Courtesy of AUDI OF AMERICA, LLC

-- If equipped, remove the front crossmember -2- and the rear crossmember -3-. Refer to Underbody Panel .

Continuation for All Vehicles

-- Remove the heat shield -1-.

-- Lower the front of the exhaust system rear section and then secure it using the Transmission Support VW785/1B, as illustrated.

Fig 7: Identifying Special Tool VW 785/1 B

Courtesy of AUDI OF AMERICA, LLC

-- Make sure there is a mark (color dot) on the driveshaft and on the rear final drive driveshaft flange -arrow A- and -arrow B-.

Fig 8: Marking Position Of Driveshaft Flange To Rear Final Drive

Courtesy of AUDI OF AMERICA, LLC

-- Make a color dot again if the original mark is no longer visible.

The dots on the driveshaft -arrow A- and on the rear final drive -arrow B- must line up.

-- Remove the driveshaft bolts -1- from the rear final drive.

Fig 9: Removing/Installing Driveshaft Bolts

Courtesy of AUDI OF AMERICA, LLC

-- Counterhold with Counterhold - Kit - Multiple Use T10172 and Counterhold - Kit - Adapter 5 T10172/5.

-- Use the Counterhold - Kit - Multiple Use - Adapter 6 T10172/6 for the rear final drive 0BE.

Fig 10: Driveshaft Center Bearing Bolts

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolts -arrows- for the driveshaft intermediate bearing.

Fig 11: Identifying Driveshaft Intermediate Bearing Mounting Bolts

Courtesy of AUDI OF AMERICA, LLC

-- Bend the driveshaft on the intermediate bearing all the way without force.

NOTE:

The driveshaft can be bent slightly further in some positions.

Turn the driveshaft slightly.

-- Guide the rear driveshaft on the fuel tank and on the rear subframe downward and remove it from the transmission.