Repair Information: Components
WARNING: This page does not describe the selected car, but rather 15 other vehicles, including the 2016 Audi S4, 2016 Audi A4 Quattro, 2015 Audi S4, 2015 Audi A4 Quattro, and 2014 Audi S4. However, it is still accessible from the selected car via links, so may be relevant.
Rear Final Drive
- Allocate bolts and other components according to final drive code .
- When installing, check the oil level in the rear final drive (Refer to GEAR OIL, CHECKING LEVEL .) and the ATF level (Refer to ATF LEVEL, CHECKING .) and fill if necessary.
- Capacities and specifications. Refer to CAPACITIES .
- Clean the contact surfaces when installing brackets and waxed components. Contact surfaces must be free of wax and grease.
- Thoroughly clean the connection points and the surrounding area before loosening.
Oil, Environmental and Disposal Regulations
- Handle ATF, transmission fluid and other oils with care.
- Dispose of drained fluid properly.
- Follow the legal environmental and disposal regulations.
- Follow the instructions listed on the fluid packaging.
ATF and Gear Oil
Rear final drive 0BF and 0BE works with separated oil chambers for the ATF and gear oil.
- For the hydraulics (hydraulic control unit and left and right chambers) use only ATF which can be obtained as replacement part. Refer to appropriate FLUID CAPACITY TABLE information in MAINTENANCE article.
- For the final drive (gear set, differential) use only the gear oil which can be obtained as replacement part. Refer to appropriate FLUID CAPACITY TABLE information in MAINTENANCE article.
- Other ATF or gear oil can cause function problems.CAUTION:
Gear oil and ATF fluid change.
- For some RS models the gear oil as well as the ATF must be changed.
- Refer to appropriate FLUID CAPACITY TABLE information in MAINTENANCE article for the change interval.
- For all other vehicles there is no change interval.
Shaft seals
- Lightly coat the shaft seal on the outer diameter with oil before installing.
- The open side on the shaft seals faces the fluid to be sealed off.
- After replacing any of the shaft seals, check the gear oil level (Refer to GEAR OIL, CHECKING LEVEL .) or the ATF level in the final drive (Refer to ATF LEVEL, CHECKING .).
Shaft Seal for the Flange/Driveshaft
- Fill the space between the sealing lips -arrow- halfway with Sealing Grease G 052 128 A1.
Flange Shaft Seals
- Coat the space between the sealing lips -arrow- with ATF.
O-Rings, Gaskets and Seals
- O-rings, gaskets and seals must always be replaced.
- After removing the seals, examine the contact surface on the housing or shaft for burrs resulting from removal or for other signs of damage.
- Thoroughly clean the housing separating surfaces before assembling.
- Lightly lubricate the O-rings before inserting to prevent the rings from being crushed during assembly.
- After replacing any of the gaskets, seal and O-rings, check the gear oil level (Refer to GEAR OIL, CHECKING LEVEL .) or the ATF level in the final drive (Refer to ATF LEVEL, CHECKING .).
Retainers
- Do not stretch the circlips.
- Always replace damaged or stretched circlips.
- The circlips must rest at the bottom of the groove.
- Replace the adapter sleeves. Installation position: the slot -A- should align with the line of force -arrow-.
Bolts and Nuts
- Always loosen or tighten bolts and nuts on covers and housings diagonally.
- Parts which are particularly sensitive must not be tilted and must be loosen or tighten diagonally in stages.
- The tightening specifications given apply to unoiled bolts and nuts.
- Always replace self-locking bolts and nuts.
- Clean threads of bolts that were applied with locking fluid using a wire brush (does not apply to driveshaft bolts: these must be replaced). Then insert the bolts with Locking Fluid AMV 185 101 A1.
- If self-locking bolts were installed or if regular bolts were installed with locking fluid, then the threaded holes must be cleaned, for example with a thread tap. Otherwise there is the risk that the bolts could break off the next time they are removed.