EVAP Canister Purge Regulator Valve 1 -N80-, CHECKING

WARNING: This page is about a different car, the 2010 Audi Q7, 2009 Audi Q7, 2008 Audi Q7, and 2007 Audi Q7. However, it is still accessible from the selected car via links, so may be relevant.

General Description

EVAP system is designed so that the admission of fuel vapors takes place only at idle and at light part-throttle. The EVAP Canister Purge Regulator Valve 1 -N80- is activated by the Engine Control Module -J623- to accomplish this task.

Special tools and workshop equipment required

Multimeter.
Wiring Diagram.
Scan Tool.

Test Requirements

Fuses OK.
Battery voltage OK.
Switch OFF All electrical and electronic accessories.
Vehicles with Auto. Transmission, ensure Selector Lever position is in "P".
Vehicles with Manual Transmission, ensure Shifter Lever position is in "N" with Parking Brake applied.
Coolant Temperature: ≥ 80° C.
Observe all safety precautions: SAFETY PRECAUTIONS .
View clean working conditions: CLEAN WORKING CONDITIONS .
For Hybrid vehicles refer to: HIGH VOLTAGE SYSTEM GENERAL WARNINGS .

Test Procedure

Step	Procedure	Result / Action to Take
1	PERFORM: Preliminary Check to verify the customers complaint. Refer to PRELIMINARY CHECK . -- Was Complaint verified?	-- YES: GO TO: Step 2 -- NO: GATHER more information from customer about the complaint.
2	IGNITION: OFF. DISCONNECT: EVAP Canister Purge Regulator Valve 1 -N80- harness connector. CHECK: EVAP Canister Purge Regulator Valve 1 -N80- component connector terminals 1 to 2 for resistance. SPECIFIED VALUE: 10 - 35 Ω (@ approx. 20° C). -- Was Value obtained?	-- YES: GO TO: Step 3 -- NO: REPLACE: EVAP Canister Purge Regulator Valve 1 -N80-. Refer to appropriate repair information. GO TO: Step 5
3	IGNITION: ON. CHECK: EVAP Canister Purge Regulator Valve 1 -N80- harness connector terminal 1 to ground for voltage. IGNITION: OFF. SPECIFIED VALUE: Battery voltage. -- Was Value obtained?	-- YES: GO TO: Step 4 -- NO: PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO: Step 5
4	REMOVE: Engine Control Module - J623-. Refer to appropriate repair information. CHECK: EVAP Canister Purge Regulator Valve 1 -N80- harness connector terminal 2 to the Engine Control Module - J623- harness connector T94 / 9 for resistance. SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω). -- Was Value obtained?	-- YES: TIP: The EVAP Canister Purge Regulator Valve 1 -N80- may fail under loaded operation; please swap a known good EVAP Canister Purge Regulator Valve 1 -N80- prior to continuing to the next step. GO TO: Step 5 -- NO: PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO: Step 5
5	Final Procedure Perform a road test to verify repair. -- Does the original DTC return?	-- YES: CHECK: Engine Control Module -J623- harness connector for any damaged, pushed-out pins. REPAIR: As necessary. If all electrical connections are OK: REPLACE: Engine Control Module -J623-. Refer to appropriate repair information. Clear the DTCs. Refer to DIAGNOSTIC MODE 04 - ERASE DTC MEMORY . Repair is complete. Generate Readiness Code. Refer to READINESS CODE . Return vehicle to Customer. -- NO: Perform the diagnostic procedure for any DTC's. If no DTC's return, the repair is complete. Return vehicle to customer.