Overview - Timing Chain Cover
- Bolt
- Replacing
- Tightening specification and sequence, refer to Fig 4.
- Shaft Seal
- For the crankshaft on the transmission side
- Replacing, refer to CRANKSHAFT SEAL, REPLACING, TRANSMISSION SIDE .
- Bolt
- Replacing
- Tightening specification and sequence, refer to Fig 4.
- Alignment Sleeve
- Quantity: 2
- Threaded Pin
- Tightening specification, refer to Fig 4.
- Left Cylinder Head Gasket
- Bolt
- Replacing
- Tightening specification and sequence, refer to Fig 2.
- Bracket
- For heat shield
- Left Timing Chain Cover
- Removing and installing, refer to LEFT AND RIGHT TIMING CHAIN COVER, REMOVING AND INSTALLING .
- Bracket
- For wiring harness
- Bolt
- Replacing
- Tightening specification and sequence, refer to Fig 2.
- Bracket
- for the left oxygen sensors electrical connectors
- Bolt
- Tightening specification and sequence, refer to Fig 2.
- Seals
- Replacing
- Bracket
- for the right oxygen sensors electrical connectors
- Bolt
- Tightening specification and sequence, refer to Fig 2.
- Bolt
- Tightening specification and sequence, refer to Fig 3.
- Bracket
- For the connectors
- Right Timing Chain Cover
- Removing and installing, refer to LEFT AND RIGHT TIMING CHAIN COVER, REMOVING AND INSTALLING .
- Right Cylinder Head Gasket
- Bracket
- For heat shield
- Bolt
- Replacing
- Tightening specification and sequence, refer to Fig 3.
- Alignment Sleeve
- Quantity: 2
- Bolt
- Tightening specification and sequence, refer to Fig 4.
- Lower Timing Chain Cover
- Removing and installing, refer to LOWER TIMING CHAIN COVER, REMOVING AND INSTALLING .
- Engine Speed Sensor -G28-
- Removing and installing, refer to Engine Speed Sensor -G28-, REMOVING AND INSTALLING .
- Bolt
- Tightening specification -item 11- OVERVIEW - IGNITION SYSTEM => List Item:Bolt .
NOTE:
Replace any bolts that were tightened with an additional turn.
The brackets -arrows A and B- are connected with the left timing chain cover.
-- Tighten the bolts in two steps in the sequence shown.
| Step | Bolts | Tightening specification/additional turn |
|---|---|---|
| 1. | -1 to 8- | 5 Nm |
| 2. | -1 to 8- | Tighten an additional 90° |
NOTE:
Replace any bolts that were tightened with an additional turn.
The brackets -arrows A and B- are attached to the right timing chain cover.
-- Tighten the bolts in two steps in the sequence shown.
| Step | Bolts | Tightening specification/additional turn |
|---|---|---|
| 1. | -1 to 8- | 5 Nm |
| 2. | -1 to 8- | Tighten an additional 90° |
NOTE:
Replace any bolts that were tightened with an additional turn.
-- Tighten bolts in stages as follows:
| Step | Bolts | Tightening specification/additional turn |
|---|---|---|
| 1. | -Arrows- | 3 Nm |
| 2. | -1 through 10- | 3 Nm diagonally |
| 3. | -1, 2, 4, 5 and 7- | Tighten an additional 90° |
| 4. | -Arrows- | 9 Nm |
| 5. | -8, 9 and 10- | 8 Nm |
| 6. | -8, 9 and 10- | Tighten an additional 90° |
| 7. | -3- | 16 Nm |
| 8. | -6- | 20 Nm |
| 9. | -6- | 180° additional turn |