DSG Transmission MECHATRONIC -J743- Overview
WARNING: This page is about a different variant/trim than selected.
- ATF Drain Plug
- Tightening specification, refer to Specifications
- Seal
- Replace
- Bolt
- Tightening specification and sequence, refer to Specifications
- Expanding Rivet
- For attaching the gasket to the ATF oil pan
- Not required for installation
- Magnet
- Quantity: 2
- Insert into the depression in the ATF oil pan
- Make sure the entire surface contacts oil pan
- Bolt
- Tightening specification and sequence, refer to Specifications
- O-rings
- Replace
- ATF Pressure Pipes (coupling pressure)
- Retaining Plate
- For the ATF pressure pipes (coupling pressure)
- Bolt
- Tightening specification, refer to Specifications
- O-rings
- Replace
- O-rings
- Replace
- ATF Oil Pipes
- Different versions, depending on date of manufacture
- O-rings
- Replace
- O-ring
- Replace
- Different versions, depending on date of manufacture
- ATF Filter Housing
- For transmissions with a replaceable ATF filter
- Different versions, depending on date of manufacture
- O-ring
- For transmissions with a replaceable ATF filter
- Replace
- ATF Filter Cover
- For transmissions with a replaceable ATF filter
- Tightening specification, refer to ATF COOLER, ATF PIPES AND ATF FILTER OVERVIEW
- ATF Filter
- Replace each time the ATF is changed and after performing a repair on the transmission
- Removing and installing, refer to ATF FILTER
- Bolt
- For transmissions with a replaceable ATF filter
- Quantity: 3
- Tightening specification, refer to ATF COOLER, ATF PIPES AND ATF FILTER OVERVIEW
- O-rings
- For transmissions with a replaceable ATF filter
- Replace
- ATF Return Pipe
- For transmissions with a replaceable ATF filter
- Removing and installing, refer to ATF PIPES .
- ATF Supply Pipe
- For transmissions with a replaceable ATF filter
- Removing and installing, refer to ATF PIPES .
- Bolt
- For transmissions with a replaceable ATF filter
- Tightening specification, refer to ATF COOLER, ATF PIPES AND ATF FILTER OVERVIEW
- Bolt
- For transmissions with an ATF pipe filter
- Quantity: 3
- Tightening specification, refer to ATF COOLER, ATF PIPES, ATF PIPE FILTER OVERVIEW
- ATF Return Pipe
- For transmissions with an ATF pipe filter
- Removing and installing, refer to ATF PIPES
- Bolt
- For transmissions with an ATF pipe filter
- Tightening specification, refer to ATF COOLER, ATF PIPES, ATF PIPE FILTER OVERVIEW
- O-rings
- For transmissions with an ATF pipe filter
- Replace
- ATF Pipe Connection
- For transmissions with an ATF pipe filter
- ATF Pipe Filter
- Replace the ATF pipe filter whenever replacing the transmission or repairing the transmission
- Removing and installing, refer to ATF PIPE FILTER
- ATF Fill and Check Plug
- Tightening specification, refer to Specifications
- O-rings
- Replace
- Bolt
- 8 Nm
- Connector Housing
-- To remove, remove the bolt -33- and turn the connector housing counter-clockwise.
- Transmission Housing
- O-rings
- Replace
- ATF Oil Pipes
- Bolt
- Tightening specification, refer to Specifications
- Cable Guide for the RPM Sensors
- Removing and installing, refer to Removal and Installation
- O-ring
- Replace
- ATF Suction Filter
- Removing and installing, refer to Removal and Installation
- DSG Transmission Mechatronic -J743-
- Removing and installing, refer to DSG TRANSMISSION MECHATRONIC -J743-
- Perform "Guided Functions" using the vehicle diagnostic tester after replacing the DSG transmission Mechatronic --, refer to TRANSMISSION GUIDED FUNCTIONS .
- Separate the circuit board from the DSG transmission Mechatronic --. Refer to Removal and Installation
- Removing and installing, refer to DSG TRANSMISSION MECHATRONIC -J743-
- Gasket
- Replace
- Installing AUTOMATIC TRANSMISSION FLUID OIL PAN
- ATF Pan
- Removing and installing, refer to AUTOMATIC TRANSMISSION FLUID OIL PAN