Version 1
WARNING: This page does not describe the selected car, but rather 15 other vehicles, including the 2008 Audi S4, 2008 Audi RS 4, 2008 Audi A4, 2007 Audi S4, and 2007 Audi RS 4. However, it is still accessible from the selected car via links, so may be relevant.
1 - Side curtain airbag connector
2 - Side curtain airbag
- Removal:
- Disconnect the battery ground (GND) strap →
- 27 BATTERY, STARTER, GENERATOR, CRUISE CONTROL
- 27 - BATTERY, STARTER, GENERATOR, CRUISE CONTROL for ELECTRICAL EQUIPMENT - GENERAL INFORMATION
- Remove sun visor → Sun visor, removing and installing .
- Remove upper trim on A-pillar → Upper A-pillar trim, removing and installing .
- Remove D-pillar trim → D-pillar trim, removing and installing .
- Remove trim above rear door → Trim above rear door, removing and installing .
- To disconnect harness connector - 1 -, open fuse using a screwdriver.
- Remove screw - 6 -.
- Loosen four bolts - 7 -.
- Remove screw - 5 -.
- Place front part of side curtain airbag module on seats.
- Loosen three bolts - 3 -.
- Remove four bolts - 4 - and remove brackets - arrows - from roof frame.
- Remove head-level airbag - 2 - from vehicle.
- Installing:
CAUTION:
Always follow side curtain airbag installation procedure.
- Insert brackets - arrows -.
- Secure four brackets -arrows- beginning from behind with four bolts - 4 -.
- Install three bolts - 3 -.
- Install last bolt - 5 -.
- Install four bolts - 7 -.
- Install bolt - 6 -.
- When connecting harness connector - 1 -, make sure that it is firmly engaged.
Further installation is performed in the reverse order of removal. Observe the following when doing so:
- Switch on ignition.
CAUTION:
No one should be in vehicle when connecting battery.
- Connect the battery ground (GND) strap →
- 27 BATTERY, STARTER, GENERATOR, CRUISE CONTROL
- 27 - BATTERY, STARTER, GENERATOR, CRUISE CONTROL for ELECTRICAL EQUIPMENT - GENERAL INFORMATION
NOTE:
- Follow safety measures after connecting battery →
- 27 BATTERY, STARTER, GENERATOR, CRUISE CONTROL
- 27 - BATTERY, STARTER, GENERATOR, CRUISE CONTROL for ELECTRICAL EQUIPMENT - GENERAL INFORMATION
- If the Airbag Malfunction Indicator Lamp (MIL) K75 shows a malfunction after assembly, DTC memory must be checked with Vehicle Diagnostic, Testing and Information System VAS 5051 A, cleared and then rechecked.
3 - Bolts (3x)
- Tightening torque 3.5 Nm
- Self-locking
- Replace after each disassembly
- Threaded holes for screws must always be cleaned (for example, with thread cutter)
4 - Screws (4x)
- Tightening torque 3.5 Nm
- Self-locking
- Replace after each disassembly
- Threaded holes for screws must always be cleaned (for example, with thread cutter)
5 - Screw
- Tightening torque 3.5 Nm
- Self-locking
- Replace after each disassembly
- Threaded holes for screws must always be cleaned (for example, with thread cutter)
6 - Screw
- Tightening torque 3.5 Nm
- Self-locking
- Replace after each disassembly
- Threaded holes for screws must always be cleaned (for example, with thread cutter)
7 - Screws (4x)
- Tightening torque 3.5 Nm
- Self-locking
- Replace after each disassembly
- Threaded holes for screws must always be cleaned (for example, with thread cutter)