Calibration Procedure with or without a Previous Axle Alignment

-- Remove the right front air intake grille:

RS Model:

-- Refer to FRONT BUMPER .

-- Remove the air guide to the coolant auxiliary cooler. Refer to AUXILIARY COOLER, REMOVING AND INSTALLING [For engine(s) CFSA] .

All Models:

-- Remove all dirt on the sensor lens.

-- If necessary, remove the mirror installed at the center and install it all the way at the right near the vertical slits.

Fig 1: Identifying Front Wheel Measuring Sensors

Courtesy of AUDI OF AMERICA, LLC

-- Position :VAS6430/1  at a distance -A- of 120 cm ± 5 cm from sensor lens to mirror surface.

Fig 2: Identifying Special Tool VAS 6430/3

Courtesy of AUDI OF AMERICA, LLC

-- Mount the front wheel measuring sensors -1- onto the :VAS6430/1  .

Fig 3: Identifying Front Wheel Measuring Sensors

Courtesy of AUDI OF AMERICA, LLC

-- In area -A-, bring item -2- on rotary knob into alignment with marking on mirror (number 2 on rotary knob must face toward vehicle).

Fig 4: Identifying Special Tool VAS 6430/3 Setup

Courtesy of AUDI OF AMERICA, LLC

-- Now align the :VAS6430/1  by sliding it sideways in direction of -arrows B- so that the laser beam is horizontally centered on the senor lens.

Fig 5: Identifying Special Tool VAS 6430/3

Courtesy of AUDI OF AMERICA, LLC

-- Level the bubble levels -A and B- on the :VAS6430/1  using the adjusting screws -1-, -2- and -3-.

Fig 6: Adjusting Special Tool VAS 6430/3 Mirror

Courtesy of AUDI OF AMERICA, LLC

-- Adjust the mirror -4- using the crank -arrow- on the :VAS6430/1  so the laser beam is vertically centered on the sensor lens.

Fig 7: Adjusting Special Tool VAS 6430/3 Mirror

Courtesy of AUDI OF AMERICA, LLC

-- Adjust the same front axle individual toe settings using fine adjustment screw -5-.

-- The difference between individual toe values must be less than 6' or they must be the same.

-- Bring bubbles -2- on measurement sensor -1- into balance.

Fig 8: Identifying Special Tool VAS 6430/3 Setup

Courtesy of AUDI OF AMERICA, LLC

-- Now using the laser beam -3- on the :VAS6430/1  , check if the laser beam contacts the sensor lens.

-- Connect the Vehicle Diagnostic Tester

The Vehicle Diagnostic Tester is ready for operation when the operating modes are displayed.

-- Turn on the ignition.

-- Touch Guided Fault Finding  .

-- Select in succession:

• Brand
• Type
• Model year
• Version
• Engine Code

-- Confirm data entered.

Wait until the Vehicle Diagnostic Tester has checked all the vehicle control module.

-- Press the go to  button and select "function/component selection".

-- Select the corresponding program in "Guided Functions".

Now follow instructions on screen to perform adjustment.

-- Turn the :VAS6190/2  in direction of -arrow A or B- and use the upper screw -2- and the lower screw -1- for precision adjustment in "Guided Fault Finding".

Fig 9: Turn VAS 6190/2 In Direction Of -Arrow A Or B- And Use Upper Screw -2- And Lower Screw -1-

Courtesy of AUDI OF AMERICA, LLC

-- Switch ignition off.

-- Disconnect the Vehicle Diagnostic Tester from the diagnostic connector.

-- Disconnect the battery charger. Refer to BATTERY .

RS Models:

-- Install the air guide to the coolant auxiliary cooler. Refer to AUXILIARY COOLER, REMOVING AND INSTALLING [For engine(s) CFSA] .

-- Install the front bumper cover. Refer to FRONT BUMPER .

All Models:

-- Install the air intake grille. Refer to FRONT BUMPER .