Camshaft Timing Chain, Removing And Installing: Installing: Notes

WARNING: This page is about a different car, the 2016 Audi A6 Quattro. However, it is still accessible from the selected car via links, so may be relevant.

Courtesy of AUDI OF AMERICA, LLC

Secure crankshaft -1- in "TDC" position using :T40237 .

NOTE:

Replace the locking bolt seal for the "TDC" marking.

Replace the bolts that were tightened with an additional turn.

-- Check whether camshafts of both cylinder heads stand in "TDC" position.

Courtesy of AUDI OF AMERICA, LLC

It must be possible to secure the camshafts with the :T40060 .
The bolt -arrow- in the :T40060 must be perpendicular to the center line of the camshaft on cylinder bank 1 (right).

The bolt -arrow- in the :T40060 must be perpendicular to the center line of the camshaft on cylinder bank 2 (left).

Courtesy of AUDI OF AMERICA, LLC

-- Remove the :T40060 from both camshafts.

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

Risk of damaging valves and piston crowns.

If camshafts are rotated, the crankshaft may not rest with any piston at "TDC".

NOTE:

If the camshafts are not secured, it is possible to correct them slightly with the :T40061 by installing the camshaft chain sprocket on the camshaft.

-- Install the left chain sprocket with the camshaft timing chain.

Courtesy of AUDI OF AMERICA, LLC

The slots in the camshaft chain sprocket must be at the middle position in relation to the threaded holes in the camshaft.

-- Next, loosely install two bolts -1- for the camshaft chain sprocket.

It must still be possible to rotate the camshaft chain sprocket on the camshaft and it must not tip.

-- Secure the left camshaft with the :T40060 .

The bolt -arrow- in the :T40060 must be perpendicular to the center axis of the camshaft.

-- Install the right camshaft chain sprocket with the camshaft timing chain.

Courtesy of AUDI OF AMERICA, LLC

The slots in the camshaft chain sprocket must be at the middle position in relation to the threaded holes in the camshaft.

-- Next, loosely install two bolts -1- for the camshaft chain sprocket.

It must still be possible to rotate the camshaft chain sprocket on the camshaft and it must not tip.

-- Secure the right camshaft with the :T40060 .

The bolt -arrow- in the :T40060 must be perpendicular to the center axis of the camshaft.

-- Secure the tensioning rail and the guide pins -2-.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the :T40316 -1- from the securing hole, thereby releasing the chain tensioner.

-- Install the bolt -arrow- for the skip protection.

-- Loosen the bolts -2-.

Courtesy of AUDI OF AMERICA, LLC

-- Stop the balance shaft -3- with the :3359 as shown in the illustration.

NOTE:

Remove the bolts if necessary and move the balance shaft into position.

-- Loosely install the bolts -2-.

It must still be possible to rotate the chain sprocket -1- on the balance shaft and it must not tip.

-- Have a second technician tension the right camshaft chain sprocket clockwise -arrow- with the :T40062 and the torque wrench to 20 Nm and maintain the pretension.

Courtesy of AUDI OF AMERICA, LLC

-- Tighten the bolts -1 and 2- to the right camshaft chain sprocket.

-- Continue to maintain the pretension and tighten the bolts -1- on the left camshaft chain sprocket.

Courtesy of AUDI OF AMERICA, LLC

-- Tighten the bolts -2- for the chain sprocket -1- for the balance shaft -3-.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the :3359 , :T40062 and :T40060 .

-- Tighten the remaining bolts for the left and right camshaft chain sprocket.

-- Remove the :3242 .

Courtesy of AUDI OF AMERICA, LLC