LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2010 >> S4 Automatic DCT >> Repair and Diagnosis >> External Pages >> Different car >> Section 946 (Wheels, Tires, Wheel Alignment & Collision Avoidance System (General & Service Information)) >> Wheels, Tires, Wheel Alignment >> Vehicle Alignment >> Axle Alignment Specified Values >> Axle Alignment Specified Values, Sedan/AVANT Front Axle

Axle Alignment Specified Values, Sedan/AVANT Front Axle

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2018 Audi S6, 2018 Audi A6 Quattro, 2018 Audi A6, 2017 Audi S6, and 2017 Audi A6 Quattro. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:

The Specified Values Apply To All Engine Versions.

  FWD/AWD
Standard Suspension 1BA / 1BH Heavy Duty Suspension (China) 1BB Sport Suspension 1BE Hybrid 1BE
Distance between the center of the wheel and lower edge of the fender 404 mm ± 10 mm 404 mm ± 10 mm 384 mm ± 10 mm 384 mm ± 10 mm
Camber (1) - 43' ± 23' - 43' ± 23' - 1° 5' ± 23' - 1° 8' ± 23'
Maximum permissible difference between both sides 30' 30' 30' 30'
Toe per wheel (adjustment value) + 10' ± 5' + 10' ± 5' + 10' ± 5' + 10' ± 5'
Toe per wheel (control value) + 10' ± 7' + 10' ± 7' + 10' ± 7' + 10' ± 7'
Toe difference angle for 20° (2) 1° 49' ± 30' 1° 49' ± 30' 1° 49' ± 30' 1° 49' ± 30'
Outer wheel steering angle at maximum steering angle 33° 24' + 1° 30' - 2° 33° 24' + 1° 30' - 2° 33° 24' + 1° 30' - 2° 33° 24' + 1° 30' - 2°
Inner wheel steering angle at maximum steering angle 39° 36' + 1° 30' - 2° 39° 36' + 1° 30' - 2° 39° 36' + 1° 30' - 2° 39° 36' + 1° 30' - 2°
(1) On RHD vehicles, the camber must be determined based on the distance between the wheel center and the lower edge of the fender. Refer to FRONT AXLE CAMBER, DETERMINING, SEDAN / AVANT, RHD .
(2) Wheel stop on outer wheel is reduced by this amount. It can also be indicated negatively in the wheel alignment computer depending on manufacturer.
  FWD/AWD
Standard Suspension Air Suspension 1BK Heavy Duty Suspension 1BR Heavy Duty Air Suspension 1BR (VW511CS China) Heavy Duty Suspension Air Suspension 1BS
Distance between the center of the wheel and lower edge of the fender 384 mm ± 10 mm 417 mm ± 10 mm 417 mm ± 10 mm 389 mm ± 10 mm
Camber (1) - 1° 5' ± 23' - 30' ± 23' - 34' ± 23' - 59' ± 23'
Maximum permissible difference between both sides 30' 30' 30' 30'
Toe per wheel (adjustment value) + 10' ± 5' + 10' ± 5' + 10' ± 5' + 10' ± 5'
Toe per wheel (control value) + 10' ± 7' + 10' ± 7' + 10' ± 7'  
Toe difference angle for 20° (2) 1° 49' ± 30' 1° 49' ± 30' 1° 49' ± 30' 1° 49' ± 30'
Outer wheel steering angle at maximum steering angle 33° 24' + 1° 30' - 2° 33° 24' + 1° 30' - 2° 33° 24' + 1° 30' - 2° 33° 24' + 1° 30' - 2°
Inner wheel steering angle at maximum steering angle 39° 36' + 1° 30' - 2° 39° 36' + 1° 30' - 2° 39° 36' + 1° 30' - 2° 39° 36 + 1° 30' - 2°
(1) On RHD vehicles, the camber must be determined based on the distance between the wheel center and the lower edge of the fender. Refer to FRONT AXLE CAMBER, DETERMINING, SEDAN / AVANT, RHD .
(2) Wheel stop on outer wheel is reduced by this amount. It can also be indicated negatively in the wheel alignment computer depending on manufacturer.
  FWD/AWD
Heavy Duty Air Suspension (China) 1BS Sport Suspension S line 1BV Allroad Air Suspension 1BY RS Suspension Air Suspension 2MA
Distance between the center of the wheel and lower edge of the fender 389 mm ± 10 mm 374 mm ± 10 mm 393 mm ± 10 mm 384 mm ± 10 mm
Camber (1) - 1° 23' ± 23' - 1° 20' ± 23' - 57' ± 23' -1° 8' ± 23'
Maximum permitted camber difference between right and left. Side of vehicle 30' 30' 30' 30'
Toe per wheel (adjustment value) + 10' ± 5' + 10' ± 5' + 10' ± 5' + 10' ± 5'
Toe per wheel (control value) + 10' ± 7' + 10' ± 7' + 10' ± 7' + 10' ± 7'
Toe difference angle for 20° (2) 1° 49' ± 30' 1° 49' ± 30' 1° 49' ± 30' 1° 49' ± 30'
Outer wheel steering angle at maximum steering angle 33° 24' + 1° 30' - 2° 33° 24' + 1° 30' - 2° 33° 24' + 1° 30' - 2° 33° 24' + 1° 30' - 2°
Inner wheel steering angle at maximum steering angle 39° 36' + 1° 30' - 2° 39° 36' + 1° 30' - 2° 39° 36' + 1° 30' - 2° 39° 36' + 1° 30' - 2°
(1) On RHD vehicles, the camber must be determined based on the distance between the wheel center and the lower edge of the fender. Refer to FRONT AXLE CAMBER, DETERMINING, SEDAN / AVANT, RHD .
(2) Wheel stop on outer wheel is reduced by this amount. It can also be indicated negatively in the wheel alignment computer depending on manufacturer.

Additional Vehicle Data For Vehicles With FWD And AWD: 

This additional vehicle data only serves for a faster diagnosis in the case of accidents.

Table. Refer to SUSPENSION .

  FWD/AWD
Sport Suspension Air Suspension 2MB RS Suspension 2MC
Distance between the center of the wheel and lower edge of the fender 384 mm ± 10 mm 389 mm ± 10 mm
Camber (1) -1° 5' ± 23' -1° 2' ± 23'
Maximum permitted camber difference between right and left. Side of vehicle 30' 30'
Toe per wheel (adjustment value) + 10' ± 5' + 10' ± 5'
Toe per wheel (control value) + 10' ± 7' + 10' ± 7'
Toe difference angle for 20° (2) 1° 49' ± 30' 1° 49' ± 30'
Outer wheel steering angle at maximum steering angle 33° 24' + 1° 30' - 2° 33° 24' + 1° 30' - 2°
Inner wheel steering angle at maximum steering angle 39° 36' + 1° 30' - 2° 39° 36' + 1° 30' - 2°
(1) On RHD vehicles, the camber must be determined based on the distance between the wheel center and the lower edge of the fender. Refer to FRONT AXLE CAMBER, DETERMINING, SEDAN / AVANT, RHD .
(2) Wheel stop on outer wheel is reduced by this amount. It can also be indicated negatively in the wheel alignment computer depending on manufacturer.
scientia non olet · About LEMON Manuals