LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2010 >> S4 Automatic DCT >> Repair and Diagnosis >> External Pages >> Different car >> Section 932 (Transmission System (Controls & Housing - Service Information - 8-Speed Automatic - 0BK AWD)) >> 37 Controls, Housing >> Selector Mechanism >> Selector Mechanism, Removing And Installing >> Removing

Selector Mechanism, Removing And Installing: Removing

WARNING: This page is about a different car, the 2018 Audi A6 Quattro, 2017 Audi A6 Quattro, and 2016 Audi A6 Quattro. However, it is still accessible from the selected car via links, so may be relevant.

-- Remove the selector lever handle. Refer to SELECTOR LEVER HANDLE, REMOVING AND INSTALLING, SIDE LOCKING BUTTON .

-- Remove the front ashtray or storage compartment. Refer to CENTER CONSOLE .

-- Move the selector lever into "D/S".

-- Insert the :T40031  through the opening -arrow- in the selector mechanism and loosen the bolt on the selector lever cable approximately one turn.

GWWA34-10994Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the connectors -2 and 4-.

GWWA37-10056Courtesy of AUDI OF AMERICA, LLC
NOTE:

The illustration does not show the insulation mat.

A second technician is needed to remove the shift mechanism under the vehicle.

Ignore -arrows-.

-- Remove the insulation mat over the shift mechanism.

-- Remove the bolts -1, 3, 5 and 6-.

-- Remove the noise insulations -1 and 2-. Refer to NOISE INSULATION .

GWWA10-11234Courtesy of AUDI OF AMERICA, LLC

-- Remove the subframe crossbrace. Refer to SUBFRAME CROSSBRACE, REMOVING AND INSTALLING .

GWWA40-10357Courtesy of AUDI OF AMERICA, LLC
CAUTION:

The suspension components could be damaged.

  • Do not rest the vehicle on its wheels if the subframe mount, the steering gear or the subframe crossbrace are not installed correctly.

Vehicles with a 3.0L TDI Biturbo Engine 

GWWA10-11496Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolts -arrows-. Press the torque support stop -1- to the engine.

-- Remove the particulate filter. .

All Vehicles 

GWWA66-10839Courtesy of AUDI OF AMERICA, LLC

-- If equipped remove the driveshaft heat shield -1- and the rear center tunnel heat shield. Refer to MOLDINGS, TRIMS, EXTENSIONS AND TRIM PANELS .

-- Remove the bolts -arrows- for the driveshaft intermediate bearing.

GWWA34-10206Courtesy of AUDI OF AMERICA, LLC

-- Lower the driveshaft.

NOTE:

The driveshaft can be bent as far as the end stop of the center joint provided that no force is used. Bending the joint forcibly to the end stop can damage the center joint and/or the protective boot.

-- Remove the lock washers -1-, (if equipped).

GWWA37-10755Courtesy of AUDI OF AMERICA, LLC

-- Pull the noise insulation -2- off the selector mechanism -4- and push it forward toward the selector lever cable -3-.

-- Remove the selector lever cable clip -1- sideways.

GWWA37-10402Courtesy of AUDI OF AMERICA, LLC

-- Remove the selector lever cable -2- from the selector mechanism.

NOTE:

Do not bend or kink the selector lever cable.

-- Mount the :T10337  on the :VAS6931  and attach it under the transmission.

GWWA37-10864Courtesy of AUDI OF AMERICA, LLC

-- Raise the transmission slightly.

WARNING:

There is the risk of an accident.

  • The :VAS6931  may only be used during assembly and must not sit unsupervised under the vehicle.

-- Remove the bolts from the tunnel crossmember -arrows-.

GWWA10-11379Courtesy of AUDI OF AMERICA, LLC

-- Lower the transmission to dimension -a- using the :VAS6931  .

GWWA10-10867Courtesy of AUDI OF AMERICA, LLC

-- Remove the selector mechanism function unit.

scientia non olet · About LEMON Manuals