Overview - Fuel Injectors

Fig 1: Fuel Injectors Exploded View

Courtesy of AUDI OF AMERICA, LLC

1. Counter PIn
   • For the tension clamp
   • Various Tightening specifications
     • 2.5 Nm on camshaft bearing
     • 9 Nm on cylinder head
2. Tensioning Claw
   • Mark fuel injector and tension bracket with paint to each other and to the cylinder for reinstallation, when installing pay attention to the markings.
   • When exchanging (as a test), the tension claw moves with the fuel injector
   • After troubleshooting, the tension claw and the fuel injector are reinstalled on the original cylinder
   • The tensioning claws can be reused, when new fuel injectors are installed.
3. Bolt
   • First tightening 6 Nm
   • Second tightening 90 degrees
   • Replacing
4. High Pressure Line
   • 25 Nm
   • From high pressure pump to fuel rail
   • Do not change the shape of the line
   • Check for damage before installing
   • Installing, refer to HIGH PRESSURE LINES, INSTALLING .
   • Coat the thread on the union nut with clean engine oil.
5. Clamp
   • For the high pressure line
6. Bolt
   • 9 Nm
7. Clamp
   • For the high pressure line
8. Bolt
   • 9 Nm
9. High Pressure Line
   • 25 Nm
   • From the opposite fuel rail
   • Do not change the shape of the line
   • Check for damage before installing
   • Installing, refer to HIGH PRESSURE LINES, INSTALLING .
   • Coat the thread on the union nut with clean engine oil.
10. Fuel rail
    • Removing and installing, refer to FUEL RAIL, REMOVING AND INSTALLING .
11. Fuel Return Hose
    • To the fuel tank
12. Fuel Return Hose
    • From the fuel injectors
    • Do not disassemble
    • Replace completely along with the restrictor
    • After replacing the engine, allow engine to idle for 2 minutes to bleed the fuel system.
    • Check the fuel return hoses for leaks.
13. Hose Connection Ring
14. Banjo Bolt
    • 25 Nm
15. Seals
    • Replacing
16. Fuel Pressure Regulator Valve -N276-
    • With biting edge for sealing
    • Cannot be used again
    • Perform an adaptation after replacing the high pressure pump and / or the Fuel Pressure Regulator Valve -N276-. Use a Vehicle Diagnostic Tester
    • Removing and installing, refer to Fuel Pressure Regulator Valve -N276-, REMOVING AND INSTALLING .
    • Tightening specification, refer to appropriate service information.
17. Bolt
    • 22 Nm
18. High Pressure Line
    • 25 Nm
    • From fuel rail to fuel injector
    • Do not change the shape of the line
    • Mark the part allocations for reinstallation and follow them when installing
    • Check for damage before installing
    • Installing, refer to HIGH PRESSURE LINES, INSTALLING .
    • Coat the thread on the union nut with clean engine oil.
19. Fuel Return Hose
    • From the fuel injectors
    • Do not disassemble
    • Replace completely along with the restrictor
    • After replacing the engine, allow engine to idle for 2 minutes to bleed the fuel system.
    • Check the fuel return hoses for leaks.
20. O-Ring
    • Replacing
21. Injector
    • Mark fuel injector and tension bracket and high pressure lines with paint to each other and to the cylinder for reinstallation, when installing pay attention to the markings.
    • When exchanging (as a test), the tension claw moves with the fuel injector
    • Replace the copper ring seal during every assembly/disassembly procedure.
    • After troubleshooting (exchange), the fuel injector and tension clamp are reinstalled on the original cylinder.
    • To remove rust particles on the fuel injector sealing surface, clean the fuel injector shaft in the cylinder head using the Cleaning Set :VAS6811  (always clean in the event of leaks).
    • Removing and installing, refer to FUEL INJECTORS, REMOVING AND INSTALLING .
22. O-Ring
    • Replacing
23. Copper Ring
    • Replace the copper ring seal during every assembly/disassembly procedure.

Courtesy of AUDI OF AMERICA, LLC

-- Align the Fuel Pressure Regulator Valve -N276- so that connecting the connector -arrow- does not cause the electrical wiring to be placed under tension.

-- Counterhold the housing hex bolt to tighten union nut on regulator valve in four stages as follows:

Courtesy of AUDI OF AMERICA, LLC

-- Tighten the Fuel Pressure Sensor -G247- in four steps as follows:

Special tools and workshop equipment required 

• Socket - 27mm :T40218 
• Torque wrench