Engine (vehicles with manual transmission), separating

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2009 Audi S4, 2008 Audi S4, 2007 Audi S4, 2006 Audi S4, and 2005 Audi S4. However, it is still accessible from the selected car via links, so may be relevant.

Special tools, testers and auxiliary items required

Support set for Audi VAS 6131/10 and VAS 6131/11

Fig 1: Adapter T40058

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Adapter T40058

Work procedure

Engine/transmission unit removed and attached to scissor lift platform VAS 6131 A.

NOTE:

All cable ties opened or cut during engine removal must be reinstalled at the same locations during installation.
All heat insulation sleeves removed during engine removal must be reinstalled at the same locations during installation.

Fig 2: Positioning Support Elements From VAS 6131/10 At Left/Right On Subframe

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Turn spindles of support elements from VAS 6131/10 at left and right at subframe completely downward.
Remove support pins from spindles.
Remove subframe to side.

Fig 3: Removing Bottom Engine/Transmission Connecting Bolts

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove bottom engine/transmission connecting bolts - arrows -.

Fig 4: Identifying Scissor Lift Platform VAS 6131

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Equip scissor lift platform VAS 6131 A with support set for Audi VAS 6131/10 and VAS 6131/11 as follows:

Platform coordinates	Parts of support set for Audi VAS 6131/10 and VAS 6131/11
B4 * See note	/10-1	/10-4	/10-5	/10-11
G3 * See note	/10-1	/10-4	/10-5	/10-11
C7	/10-1	/10-4	/10-5	/10-12
G7	/10-1	/10-4	/10-5	/10-12
F10	/10-1	/10-4	/10-5	/11-3
D12	/10-1	/10-2	/10-5	/11-2
C14 * See note	/10-1	/10-3	/10-5	/10-7
E14 * See note	/10-1	/10-3	/10-5	/10-7

*Support elements remain unchanged.

Fig 5: Positioning Support Elements From VAS 6131/10 And VAS 6131/11 At Left On Engine/Transmission

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Position support elements from VAS 6131/10 and VAS 6131/11 at left on engine/transmission as shown in illustration.

Fig 6: Positioning Support Elements From VAS 6131/10 And VAS 6131/11 At Right On Engine/Transmission

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Position support elements from VAS 6131/10 and VAS 6131/11 at right on engine/transmission as shown in illustration.
Turn spindles of attachments upward far enough until all support pins make contact at support points.
Tighten base plates for support elements to 20 Nm on scissor lift platform VAS 6131 A.

Fig 7: Removing Bracket For Electrical Harness Connectors At Left From Bulkhead

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove electrical harness connectors - 1 - and - 4 - from bracket and disconnect.
Remove heat insulation sleeve on wiring harness and free up individual wires.

NOTE:

In the illustration, the electrical harness connectors are depicted as installed.

Fig 8: Removing Bolt At Strap For Left Front Exhaust Pipe

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove bolt - arrow - at strap for left front exhaust pipe.

Fig 9: Removing Nuts For Left Front Exhaust Pipe/Exhaust Manifold

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove nuts - 1 to 3 - for left front exhaust pipe/exhaust manifold.
Remove front exhaust pipe with pre- and main catalytic converters.

Fig 10: Removing Electrical Harness Connectors From Bracket

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove electrical harness connectors - 2 - and - 4 - from bracket and disconnect.
Free up wiring harnesses.

NOTE:

In the illustration, the electrical harness connectors are depicted as installed.

Fig 11: Removing Bolt At Strap For Right Front Exhaust Pipe

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove bolt - arrow - at strap for right front exhaust pipe.

Fig 12: Removing Nuts For Right Front Exhaust Pipe/Exhaust Manifold

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove nuts - 1 to 3 - for right front exhaust pipe/exhaust manifold.
Remove front exhaust pipe with pre- and main catalytic converters.

Fig 13: Location Of Engine Speed (RPM) Sensor G28 On Coupling Housing

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove bolt and Engine Speed (RPM) Sensor G28 on transmission - arrow -.

Fig 14: Disconnecting Electrical Harness Connector At Back-Up Light Switch F4

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Disconnect electrical harness connector - arrow - at Back-Up Light Switch F4 and free up electrical wire.

Fig 15: Identifying Engine/Transmission Threaded Connections

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove engine/transmission threaded connections - 1 to 7 -.

Fig 16: Locating Clamping Bolts On Side Of Scissor Lift Table VAS 6131 And Pull Rear Table Section With Transmission Rearward

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Loosen side clamping bolts - 1 - on scissor lift platform VAS 6131 A and pull rear platform top with transmission toward rear - arrow - , simultaneously push torque converter through opening of drive plate while doing this.