LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2010 >> S4 Automatic DCT >> Repair and Diagnosis >> External Pages >> Different car >> Section 565 (Controls & Housing - S TRONIC Transmission 0B5 (Sedan)) >> 34 Controls, Housing >> Transmission, Removing And Installing >> Transmission Tightening Specifications

Transmission Tightening Specifications

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2018 Audi S6, 2017 Audi S6, 2016 Audi S6, 2016 Audi S4, and 2015 Audi S4. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:

The tightening specifications apply only to lightly greased, oiled, phosphated or blackened nuts and bolts.

Additional lubricant such as engine oil or transmission fluid may be used, but do not use graphite lubricant.

Do not use any ungreased parts.

Tightening specification tolerance ± 15%.

Component Nm
Bolts and nuts M6 9
M7 15
M8 20
M10 40
M12 65
Fig 1: Drive Axle Heat Shield & Bolts
GWWA37-10841Courtesy of AUDI OF AMERICA, LLC

-- Tighten the heat shield bolts -arrows- to 23 Nm.

S tronic Transmission to 6-Cylinder Gasoline Engine 

Fig 2: Checking If Alignment Sleeves -A- For Centering Engine/Transmission Are In Cylinder Block
GWWA34-10471Courtesy of AUDI OF AMERICA, LLC
Item Bolt Nm
1 1) M10x50 2) 65
2 1) , 3, 4 to 6 M12x100 3) 30 + 90°
7 M12x125 3) 30 + 90°
8 M10x60 3) 15 + 90°
9, 10 M10x60 3) 15 + 90°
A Alignment sleeve for centering
  1. Mount the auxiliary adapter
  2. Bolt strength rating 10.9. There is no limit to the number of times steel bolts may be used.
  3. The aluminum bolts may be used 2 times (1), (2).
(1) The aluminum bolts -2 through 10- can be used twice. Therefore, the bolts must be marked with two notches "X" made by a chisel after they have be used the first time -arrow- (See Fig 4).

(2) To prevent damaging the bolts when marking them, do not clamp them in a vise. Insert the bolt using a 14 mm socket with a 1/2 drive, which is inserted in to the vise, as illustrated.

S tronic Transmission to the 8-Cylinder Gasoline Engine (RS5, RS4) 

Fig 3: Checking If Alignment Sleeves -A- For Centering Engine/Transmission Are In Cylinder Block
GWWA34-10471Courtesy of AUDI OF AMERICA, LLC
Item Bolt Nm
1 1) M10x50 2) 65
2, 1) , 3, 4, 5, and 6 M12x100 3) 30 + 90°
7 4) M12 x 175 3) 30 + 90°
8, 9, 10 M10x60 3) 15 +90°
A Alignment sleeve for centering
  1. Mount the auxiliary adapter
  2. Bolt strength rating 10.9 There is no limit to the number of times the steel bolt can be used again.
  3. Aluminum bolts can be used twice (1), (2).
  4. Vehicles with electro-mechanical power steering: with nut and washer. Counterhold the nut when loosening and tightening.
(1) The aluminum bolts -2 through 10- can be used twice. Therefore, the bolts must be marked with two notches "X" made by a chisel after they have be used the first time -arrow- (See Fig 4).

(2) To prevent damaging the bolts when marking them, do not clamp them in a vise. Insert the bolt using a 14 mm socket with a 1/2 drive, which is inserted in to the vise, as illustrated.
scientia non olet · About LEMON Manuals