DTC Chart: HCM

WARNING: This page is about a different car, the 2018 Lincoln Navigator. However, it is still accessible from the selected car via links, so may be relevant.

Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .

DTC	Description	Action
C1A03:29	Left Front Height Sensor: Signal Invalid	GO to Pinpoint Test Q
C1A05:29	Left Rear Height Sensor: Signal Invalid	GO to Pinpoint Test Q
B103C:01	Left Headlamp Control: General Electrical Failure	GO to Pinpoint Test R
B103C:55	Left Headlamp Control: Not Configured	GO to Pinpoint Test R
B103C:96	Left Headlamp Control: Component Internal Failure	GO to Pinpoint Test R
B103D:01	Right Headlamp Control: General Electrical Failure	GO to Pinpoint Test R
B103D:55	Right Headlamp Control: Not Configured	GO to Pinpoint Test R
B103D:96	Right Headlamp Control: Component Internal Failure	GO to Pinpoint Test R
B1041:54	Levelling Control: Missing Calibration	Using a diagnostic scan tool, carry out the Ride Height Calibration routine. Follow the scan tool directions. Using a diagnostic scan tool, carry out the HCM self-test. If the DTC returns, INSTALL a new HCM. REFER to: Headlamp Control Module (HCM) .
B1087:00	LIN Bus "A": No Sub Type Information	GO to Pinpoint Test C
B1088:00	LIN Bus "B": No Sub Type Information	GO to Pinpoint Test C
B14D9:92	Left Headlamp Light Distribution Actuator: Performance or Incorrect Operation	Using a diagnostic scan tool, carry out the Ride Height Calibration routine. Follow the scan tool directions. Using a diagnostic scan tool, carry out the HCM self-test. If the DTC returns, INSTALL a new headlamp assembly. REFER to: Headlamp Assembly .
B14DA:92	Right Headlamp Light Distribution Actuator: Performance or Incorrect Operation	Using a diagnostic scan tool, carry out the Ride Height Calibration routine. Follow the scan tool directions. Using a diagnostic scan tool, carry out the HCM self-test. If the DTC returns, INSTALL a new headlamp assembly. REFER to: Headlamp Assembly .
U0100:00	Lost Communication With ECM/PCM "A": No Sub Type Information	GO to Pinpoint Test G
U0101:00	Lost Communication With TCM: No Sub Type Information	GO to Pinpoint Test H
U0121:00	Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information	GO to Pinpoint Test I
U0122:00	Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information	GO to Pinpoint Test J
U0140:00	Lost Communication With Body Control Module: No Sub Type Information	GO to Pinpoint Test K
U0151:00	Lost Communication With Restraints Control Module: No Sub Type Information	GO to Pinpoint Test L
U0155:00	Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information	GO to Pinpoint Test M
U0212:00	Lost Communication With Steering Column Control Module: No Sub Type Information	GO to Pinpoint Test N
U023A:00	Lost Communication With Image Processing Module A: No Sub Type Information	GO to Pinpoint Test O
U0401:00	Invalid Data Received from ECM/PCM A: No Sub Type Information	This DTC sets when the HCM receives invalid network data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID) .
U0402:00	Invalid Data Received From TCM: No Sub Type Information	This DTC sets when the HCM receives invalid network data from the TCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the TCM and other modules on the network. REFER to: Diagnostic Trouble Code (DTC) Charts and Pinpoint Tests - 3.5L EcoBoost (272kW/370PS) .
U0415:00	Invalid Data Received From Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information	This DTC sets when the HCM receives invalid network data from the ABS module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the ABS module and other modules on the network. REFER to: Anti-Lock Brake System (ABS) and Stability Control (206-09 Anti-Lock Brake System (ABS) and Stability Control).
U0416:00	Invalid Data Received From Vehicle Dynamics Control Module: No Sub Type Information	This DTC sets when the HCM receives invalid network data from the VDM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the VDM and other modules on the network. REFER to: Vehicle Dynamic Suspension .
U0422:00	Invalid Data Received From Body Control Module: No Sub Type Information	This DTC sets when the HCM receives invalid network data from the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. REFER to: Body Control Module (BCM) .
U0429:00	Invalid Data received from Steering Column Control Module: No Sub Type Information	This DTC sets when the HCM receives invalid network data from the SCCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the SCCM and other modules on the network. REFER to: Steering Wheel and Column Electrical Components .
U0452:00	Invalid Data Received From Restraints Control Module: No Sub Type Information	This DTC sets when the HCM receives invalid network data from the RCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the RCM and other modules on the network. REFER to: Airbag Supplemental Restraint System (SRS) (501-20 Supplemental Restraint System).
U2100:00	Initial Configuration Not Complete: No Sub Type Information	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. REFER to: Module Programming . If there have been no recent service actions, INSTALL a new adaptive front lighting module. REFER to: Adaptive Front Lighting Module .
U2101:00	Control Module Configuration Incompatible: No Sub Type Information	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMIprocedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to: Module Programming . If there have been no recent service actions, INSTALL a new HCM to correct the failure to retain configuration data. REFER to: Headlamp Control Module (HCM) .
U3000:49	Control Module: Internal Electronic Failure	CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new HCM. REFER to: Headlamp Control Module (HCM) .