Final Drive Removing And INSTALLIN G 0BC, AUDI A4, A5, A6, A7, And Q5 (Except Q5 Hybrid): Installing

WARNING: This page does not describe the selected car, but rather 13 other vehicles, including the 2017 Audi SQ5, 2017 Audi Q5, 2016 Audi SQ5, 2016 Audi Q5, and 2015 Audi SQ5. However, it is still accessible from the selected car via links, so may be relevant.

Install in reverse order of removal. Pay attention to the following:

Tightening specifications. Refer to OVERVIEW - FINAL DRIVE 0BC, 0BD .

-- With a second technician, position the rear final drive -1- on the subframe -2- in its installed position.

Fig 1: Mount Rear Final Drive On Subframe

Courtesy of AUDI OF AMERICA, LLC

-- Insert the left drive axle -3- into the final drive flange shaft.

-- The second technician must now push the rear final drive -1- toward the left side of the vehicle in direction of -arrow-.

-- Then install the right drive axle -5- into the final drive flange shaft -4-.

-- Remove the Engine and Gearbox Jack VAS6931 with the Engine/Gearbox Jack Adapter - Wheel Hub Support T10149 from the left rear suspension.

-- Position the Engine and Gearbox Jack VAS6931 and the Universal Transmission Support VAG1359/2 and a block of wood (approximately 80 mm tall) under the rear final drive -A-.

Fig 2: Placing VAG 1383 A With VAG 1359/2 And A Block Of Wood

Courtesy of AUDI OF AMERICA, LLC

-- Move the final drive -A- forward slightly.

-- Turn the upper crossmember -B- opposite the direction of -arrow 1- to the left and insert it while guiding it past the final drive -arrow 2-.

-- Tighten the bolts connecting the crossmember -B- to the rear final drive diagonally. Tightening specification, refer to -item 4- Bolt (See Figure).

Fig 3: Guiding T40154 Through Holes In Subframe -A-

Courtesy of AUDI OF AMERICA, LLC

-- Guide the Socket - Xzn 12 T40154 through the holes in the subframe -A-. Move the final drive to the left or right just a little, if necessary.

-- First tighten the bolt -2 and 4- hand-tight.

Fig 4: Removing Left And Right Driveshaft

Courtesy of AUDI OF AMERICA, LLC

NOTE:

For better illustration the Engine and Gearbox Jack VAS6931 with the Universal Transmission Support VAG1359/2 are not shown.

-- Tighten the bolt -4-. Tightening specification, refer to -item 3- Bolt (See Figure).

-- Tighten the bolts -2-. Tightening specification, refer to -item 2- Bolt (See Figure).

-- Remove the Engine and Gearbox Jack VAS6931 from under the final drive.

-- Tighten the left -1- and right -3- drive axles. Refer to DRIVE AXLE, REMOVING AND INSTALLING .

-- Attach the left driveshaft heat shield -A- to the crossmember/rear final drive -arrows-. Refer to -item 6- Bolt (See Figure).

Fig 5: Removing Left Driveshaft Head Shield

Courtesy of AUDI OF AMERICA, LLC

-- Attach the driveshaft to the rear final drive. Refer to INSTALLING .

Fig 6: Identifying Driveshaft Intermediate Bearing Mounting Bolts

Courtesy of AUDI OF AMERICA, LLC

-- Attach the driveshaft intermediate bearing to the body free of tension. Tightening specification. Refer to -item 8- Bolt (See Figure).

-- Check the gear oil level in the rear final drive. Refer to GEAR OIL, CHECKING LEVEL, 0BC .

-- Attach the heat shield -3- to the body -arrows-.

Fig 7: Attaching Heat Shield -3- To Body -Arrows-

Courtesy of AUDI OF AMERICA, LLC

-- Install the rear section of the exhaust system and align it so it is free of tension. Refer to EXHAUST SYSTEM, INSTALLING WITHOUT TENSION .

-- If equipped, install the cross member -1-. Refer to Underbody Panel .

-- Install the left rear wheel and tighten. Refer to TIRES, CHANGING .