Starter - 4.2L 8-cylinder engine (Audi S4), removing and installing

Special tools, testers and auxiliary items required

Fig 1: Identifying 10-222A Engine Support Bridge With 10-222A/8 Bracket For Engine

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Engine support bridge 10-222 A

Fig 2: Identifying Special Tools - Shackle 10 - 222 A/12

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Shackle (set) 10-222 A/12

Fig 3: Identifying Torque Wrench V.A.G. 1331

Courtesy of VOLKSWAGEN UNITED STATES, INC.

VAG 1331 Torque wrench (or 5 - 50 Nm equivalent)

Fig 4: Identifying Torque Wrench V.A.G. 1332

Courtesy of VOLKSWAGEN UNITED STATES, INC.

VAG 1332 Torque wrench (or 40 - 200 Nm equivalent)

Removing

Disconnect battery → Battery in engine compartment, disconnecting and reconnecting .

Fig 5: Removing/Installing Rear Engine Cover

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Unclip engine cover - arrows -.

Fig 6: Securing Shackle 10-222 A/12 To Right Rear Engine Lifting Eyelet

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Attach shackle 10-222 A/12 to right rear lifting fixture on engine.

NOTE:

Disregard - 1 -.

Fig 7: Engaging Shackle 10-222 A/12 On Spindle Of Engine Support Bridge 10-222 A

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Assemble support bracket 10-222 A and place across fenders as illustrated.
Attach shackle to lifting spindle.
Turn lifting spindle to apply slight lifting tension to engine.
Lift vehicle.

Remove right front wheel.

Fig 8: Removing Quick-Release Fasteners, Screws And Noise Insulation

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Release fasteners - 1 - , remove bolts - 2 - and remove noise insulation.

Fig 9: Removing Nuts For Left/Right Stabilizer Mounts

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove anti-roll bar bracket nuts - 1... 4 -.

Fig 10: Removing Wiring Harness Bracket At Right Engine Mount Plate

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove nut - arrow - and remove harness retainer from mounting.

Fig 11: Identifying Nuts, Bolts, And Right Side Engine Mount Carrier

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove nut - 3 -.
Remove bolts - 1 - and - 2 - and remove right side engine mount carrier.

Fig 12: Removing Refrigerant Line On Bracket

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove right refrigerant line mounting - arrow -.

Fig 13: Disconnecting Electrical Harness Connector At Right Engine Mount

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Disconnect electrical connection - 1 -.
Remove bolts - arrows -.
Remove right engine mount with bracket.

Fig 14: Drive Axle Heat Shield

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Vehicles with manual transmission:

Remove right drive shaft heat shield - arrow -.

Fig 15: Identifying Ground (GND) Wire, Wires, Nuts, Bolts & Starter

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove ground cable - 5 -.
Remove nut at starter solenoid terminal B+ - 3 - and connection for terminal 50 - 4 -.
Remove nut - 1 - and bolt - 2 -.
Remove starter.

Fig 16: Removing Left/Right Heat Shields For Drive Axles

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Vehicles with automatic transmission:

Remove heat shield - 1 - for drive shaft (right-side).

Fig 17: Identifying Ground (GND) Wire, Starter Electrical Wires, Bolts & Starter

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove earth cable - 1 -.
Remove nut at starter solenoid terminal B+ - 3 - and connection for terminal 50 - 4 -.
Remove bolts - 2 - and - 5 -.
Remove starter.

Installing

Install in reverse order of removal, noting the following:

Install engine mounting and tighten subframe → 40 - FRONT SUSPENSION .
Install anti-roll bar → 40 - FRONT SUSPENSION .
Reconnect battery. Required steps Reconnecting .

Tightening torques

Component - fastener	Nm
Starter to transmission - bolt	65
Terminal B+ to starter - nut	16
Ground cable to starter - bolt	22
Engine support to cylinder block - bolt	42 ¹⁾
Drive shaft heat shield to transmission - bolt	23
¹⁾ Insert with locking compound; locking compound.