LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2006 >> TT Base, 2D Convertible >> Repair and Diagnosis >> Engine Mechanical >> Starter >> Electrical Equipment >> 01 On Board Diagnostic (OBD) >> Instrument cluster through m.y. 2000 - VIN 8N_Y040001 and/or software versions from D26 & D03, On Board Diagnostic (OBD) >> Diagnostic Trouble Code (DTC) table

Diagnostic Trouble Code (DTC) table

NOTE:
  • The following table lists all the malfunctions that can be recognized by the instrument cluster and printed out by the VAG 1551. The DTCs are listed in order according to their 5-figure code numbers.
  • DTCs appear only on print-out.
  • Before replacing a component shown as malfunctioning, check wiring and connections to the component as well as Ground connections according to the wiring diagram.
  • After completing a repair and checking the function of the system, always check the Diagnostic Trouble Code (DTC) memory once again with the VAG 1551 scan tool and erase the memory.
  • The Diagnostic Trouble Code (DTC) memory records all static and sporadic malfunctions. If a malfunction occurs and persists for at least 2 seconds, it is identified as a static malfunction. (In the case of the ambient temperature display, a malfunction must persist for at least 60 seconds before it is classified as a static malfunction; in the case of the coolant temperature sender, static malfunctions are those which persist for at least 30 minutes with the engine running). If the malfunction does not occur again it is registered as a sporadic malfunction and the letters "/SP" will appear at the right of the display.
  • When the ignition is switched on, all existing malfunctions are automatically re-classified as sporadic malfunctions and will only register as static malfunctions if they still occur after testing.
  • Sporadic malfunctions which no longer occur after 50 driving cycles (ignition on for at least 5 minutes, road speed of more than 30 km/h) are erased automatically.
VAG 1551 scan tool display  Possible causes  Corrective action 
005621)     
Oil Level Thermo Sensor -G2661)    
  • Open/short circuit to B+
  • Short circuit to Ground
  • Implausible signal
  • Open circuit in wiring or short between oil level/temperature sender -G266 and instrument cluster
  • -G266- malfunctioning
  • Sender electronics malfunctioning
  • Repair open or short circuit in wiring using wiring diagram
  • Replace -G266-
00667     
Ambient-temperature signal    
  • Open/short circuit to B+
  • Short circuit to Ground
  • Open circuit or short circuit between instrument cluster and A/C control head -E87
  • -E87 malfunctioning
  • Outside Air Temperature Sensor -G17 malfunctioning
  • Repair open or short circuit in wiring using wiring diagram
  • Perfom OBD program. Refer to 87 AIR CONDITIONING
    • Replace -G17
00668     
Battery Positive Voltage (B+) Term. 30    
  • Voltage supply too low
  • Battery disconnected or totally discharged
  • Open circuit in wiring or short circuit at control module or sender
  • Perform automatic test sequence (function 00) to identify affected control module
  • Repair open or short circuit in wiring using wiring diagram
  • Erase DTC memory and road test

1) Where applicable. Component function may not be coded for US/CDN market.

VAG 1551 scan tool display  Possible causes  Corrective action 
00771     
Fuel level Sensor -G    
  • Open/short circuit to B+
  • Short circuit to Ground
  • Open circuit or short circuit between fuel level sensor -G- and instrument cluster
  • Fuel level sensor -G- (front-wheel drive/quattro) or -G169 (quattro) malfunctioning
  • Repair open or short circuit in wiring using wiring diagram
  • Replace -G- (front-wheel drive/quattro) or -G169 (quattro)
00779     
Outside Air Temperature Sensor -G17    
  • Open/short circuit to B+
  • Short circuit to Ground
 Vehicles without air conditioner:
  • Open circuit or short circuit between -G17- and instrument cluster
  • -G17- malfunctioning
 Vehicles without air conditioner:
  • Repair open or short circuit in wiring using wiring diagram
  • Replace -G17-
01039     
ECT Sensor -G2    
  • Open/short circuit to B+
  • Short circuit to Ground
  • Open circuit or short circuit between -G2 and instrument cluster
  • -G2 malfunctioning
  • Repair open or short circuit in wiring using wiring diagram
  • Replace -G2
VAG 1551 scan tool display  Possible causes  Corrective action 
013002)     
Control Module for Nav. w/CD) -J401-2)    
  • No communication
  • Open/short circuit between -J401- and instrument cluster
  • -J401 without CAN-Bus capability installed
  • Instrument cluster adaptation not performed properly
  • Repair open or short circuit in wiring using wiring diagram
  • Check CAN-Bus capability of control module by confirming that value "1" appears in Read Measuring Value Block 140. Refer to Read Measuring Value Block (function 08) 
  • Perfom Adaptation (function 10), select channel 62 and enter correct adaptation value. Refer to Adaptation (function 10) 

2) Where applicable.

VAG 1551 scan tool display  Possible causes  Corrective action 
01311     
Data Bus Information    
  • Faulty
  • In 1-wire operation
  • Open/short circuit between control module and Information CAN-Bus network
  • Control module without CAN-Bus capability installed
  • Control module with CAN-Bus capability and instrument cluster not adapted
  • CAN-Bus in one wire operation (possibility of electro-magnetic compatibility problems)
  • Repair open or short circuit in wiring using wiring diagram
  • Check CAN-Bus capability of control module by confirming that value "1" appears in Read Measuring Value Block 140. Refer to Read Measuring Value Block (function 08) 
  • Perfom Adaptation (function 10), select channel 62 and enter correct adaptation value. Refer to Adaptation (function 10) 
65535     
Control Module Malfunctioning Instrument cluster malfunctioning
scientia non olet · About LEMON Manuals