Output Diagnostic Test Mode (function 03)
The Output Diagnostic Test Mode enables you to check the function of the final control elements, which are the actuators (e.g. solenoid valves, relays or pump motors) energized by the control module after processing the incoming signals from the sensors.
- Output Diagnostic Test Mode can only be performed on vehicles with control modules No. 8D0 407 389 A/D/E.
- Output Diagnostic Test Mode is not possible for vehicles with control module No. 4B0 907 389.
- When the ignition is switched on, the Output Diagnostic Test Mode procedure should only be performed once; it cannot be repeated while the ignition is on.
The function of the final control elements includes all functions and properties of the final control elements under operating conditions, for example:
- An electrically operated hydraulic valve which opens and closes when activated by the control module.
- The relay of an electric motor which starts the motor when activated by the control module. The motor should then run and deliver the required power.
It is advantageous to ensure that there are no electrical malfunctions in the system to be tested. This will enable you to recognize mechanical malfunctions. Perform a targeted troubleshooting procedure before the OUTPUT DIAGNOSTIC TEST MODE (FUNCTION 03) .
When you have made sure that there are no electrical malfunctions in the system, you will be able to identify any mechanical malfunctions in the individual control elements (actuators) if the results of the diagnosis are not as specified on the following pages. In this case, replace the affected component.
With the Bosch 5.3 ABS/ESP system the Output Diagnostic Test Mode enables you to check the electrically actuated hydraulic valves and the pump motor in the hydraulic control module. You can also check that the brake lines going to the four wheels are connected correctly.
- The vehicle must be raised until all wheels are free to turn. A second technician is required to check whether the wheels are locked or can be turned.
- The -C- button can be used to exit from the test sequence at any time.
- To avoid overloading the final control elements they are only actuated during the test sequence for a period of 60 (or 90) seconds. The final control test will be terminated if the --> button is not pressed within this period.
- The ABS/EDL warning light and the brake system warning symbol flash during the Output Diagnostic Test Mode.
- If the brake pedal is pressed repeatedly this will exhaust the vacuum in the brake servo. For this reason, the brake pedal must be pressed harder in order to achieve the same braking effect. It may be advisable to start the engine briefly to build up vacuum in the servo.
When you perform the function "Output Diagnostic Test Mode" the individual test steps are shown in the second line of the display on VAG 1551 scan tool. The following abbreviations are used:
I = Inlet valve
O = Outlet valve
FL = Front Left
FR = Front Right
RL = Rear Left
RR = Rear Right
VBAT = Battery voltage at valve
0V = 0 Volt; No voltage at valve
Locked/free = Wheel condition; must be checked by 2nd technician
Hydr-P = Hydraulic pump
- Connect VAS 5051 vehicle diagnostic, testing and information system or VAG 1551 scan tool and select address word 03 for "Brake electronics". See VAG 1551 SCAN TOOL, CONNECTING AND ENTERING ADDRESS WORD .
- Check the control module version. See CHECK CONTROL MODULE VERSIONS (FUNCTION 01) and press --> button.
Indicated on display
- Press buttons -0- and -3- for the function "Output Diagnostic Test Mode".
Indicated on display
- Press -Q- button to confirm input.
Indicated on display
ABS return flow pump -V39- should start running audibly.
When you put your foot on the brake pedal you can feel it vibrating. See Fig 4 . This is because the hydraulic pump is producing pressure pulses in the brake lines, which induce the vibrations that can be felt at the pedal.
The pressure pulses in the brake lines are not sufficient to lock the wheels.
Fig 5 is a schematic diagram of the hydraulic circuit of an ABS/EDL system. This will give a better understanding of the various test steps in the Output Diagnostic Test Mode.
- The grey-shaded components are active.
- Thin solid lines represent hydraulic lines or hoses which are not under pressure.
- Thick broken lines represent hydraulic lines or hoses working as suction lines.
- Thick solid lines represent hydraulic lines or hoses which are under pressure.
- Press --> button.
Indicated on display
- Press --> button.
Indicated on display
When you press the brake pedal, brake fluid pressure will be built up in all four wheel brake cylinders. See Fig 8 . All four wheels will be locked.
This assumes that the mechanical and hydraulic components of the brake system are working properly, which means that the master cylinder is able to build up pressure in all four wheel brake cylinders and there are no leaks in the hydraulic lines, hoses and connections.
If the wheels do not lock, perform a visual inspection of the brake fluid reservoir, the master cylinder, the hydraulic unit and the wheel cylinders.
To start with, however, concentrate on the left front wheel. The function of the control elements for this wheel is tested first.
- Press --> button.
Indicated on display
Keep pressing the brake pedal.
The inlet valve is activated, which interrupts the brake line. See Fig 11 . However, the fluid pressure is still maintained in the wheel cylinder. The left front wheel remains locked.
- Press --> button.
Indicated on display
Keep pressing the brake pedal. The inlet valve and the outlet valve for the left front wheel are activated. See Fig 13 . The hydraulic pump starts running and reduces the fluid pressure in the wheel cylinder via the open outlet valve.
The brake pedal must not give, and should press back harder against your foot.
You should now be able to turn the left front wheel.
If you cannot turn the wheel, check whether the brake line for the left front wheel is correctly connected.
If this is the case, this indicates that there is a mechanical malfunction in one of the valves, providing that there is no electrical malfunction in the system. Replace the hydraulic control module.
If the brake pedal gives under your foot, this means that the inlet valve or the non-return valve connected in parallel with the inlet valve is leaking. Replace the hydraulic control module.
- Press --> button.
Indicated on display
ABS return flow pump -V39- will stop running.
Keep pressing the brake pedal. Only the inlet valve is now activated, and this interrupts the brake line. See Fig 16 . If the inlet valve is not leaking you should be able to turn the front left wheel.
If you cannot turn the wheel, this means that the inlet valve or the non-return valve connected in parallel with the inlet valve is leaking. Replace the hydraulic control module.
- Press --> button.
Indicated on display
Keep pressing the brake pedal. The inlet valve is no longer activated and does not interrupt the brake line. See Fig 18 . The brake pedal will give perceptibly under your foot. Fluid pressure is built up again in the front left wheel cylinder. The wheel will be locked.
- Press --> button.
Indicated on display
- Press --> button.
Continue the Output Diagnostic Test Mode in order to check the right front, left rear and right rear wheels in turn. The test steps are the same as for the left front wheel, so they are not described in detail.
Indicated on display
- Press --> button.
Indicated on display
- Press --> button.
Indicated on display
- Press --> button.
ABS return flow pump -V39- should start running.
Brake pedal must not give.
Indicated on display
- Press --> button.
ABS return flow pump -V39- will stop running.
Indicated on display
- Press --> button.
Brake pedal should give perceptibly.
Indicated on display
- Press --> button.
Indicated on display
- Press --> button.
Indicated on display
- Press --> button.
Indicated on display
- Press --> button.
Indicated on display
- Press --> button.
ABS return flow pump -V39- should start running.
Brake pedal must not give.
Indicated on display
- Press --> button.
ABS return flow pump -V39- will stop running.
Indicated on display
- Press --> button.
Brake pedal should give perceptibly.
Indicated on display
- Press --> button.
Indicated on display
- Press --> button.
Indicated on display
- Press --> button.
Indicated on display
- Press --> button.
Indicated on display
- Press --> button.
ABS return flow pump -V39- should start running.
Brake pedal must not give.
Indicated on display
- Press --> button.
ABS return flow pump -V39- will stop running.
Indicated on display
- Press --> button.
Brake pedal should give perceptibly.
Indicated on display
- Press --> button.
Indicated on display
- Press --> button.
Indicated on display
The EDL change-over valve (left) and the EDL inlet valve are activated. ABS return flow pump -V39- runs for one second. See Fig 42 . The pump draws brake fluid out of the fluid reservoir via the EDL inlet valve, and builds up pressure in the EDL-controlled wheel cylinders. These wheels will then be locked.
If this is not the case, this indicates that there is a mechanical malfunction in one of the valves, provided that there are no electrical malfunctions in the system. Replace the hydraulic control module.
- Press --> button.
Indicated on display
- Press --> button.
Indicated on display
- Press buttons -0- and -6- for the function "End Output" and confirm entry with the -Q- button.