Diagnostic Trouble Code (DTC) table
NOTE:
- The following table contains all possible malfunctions that are recognized by the Transmission Control Module (TCM) -J217- and displayed by the VAG 1551 or VAG 1552 Scan Tool (ST) when the Diagnostic Trouble Code (DTC) memory is checked.
- The DTC is printed out in the "Rapid data transfer" operating mode only when the printer of the VAG 1551 scan tool is switched on. Example: DTC 17087P0703 (VAG code and P-code).
- If malfunctions occur occasionally or if the DTC memory was not erased after corrective actions, these malfunctions are indicated as "sporadic" for a specified amount of time. Malfunction recognition by the TCM, see TRANSMISSION CONTROLS .
- If components are determined to be malfunctioning when the DTC memory is checked, check the wiring to the components for a short circuit and open circuit.
See appropriate System Wiring Diagrams .
- "Dcy " means "driving cycle." Conditions for recognition of a driving cycle (Dcy), see MIL FUNCTIONAL CHECK .
- Malfunction Indicator Lamp (MIL) function, see MALFUNCTION INDICATOR LAMP (MIL), FUNCTION
- The "MIL" column in the DTC table indicates the conditions for which the MIL will be switched on. If, for example, "2 Dcy" is indicated, it means that the MIL will be switched on after 2 driving cycles. If "Off" is indicated, the malfunction has no influence on the MIL. If "On" is indicated, the MIL will be switched on immediately when the malfunction occurs.
- For Output Diagnostic Test Mode, see OUTPUT DIAGNOSTIC TEST MODE (DTM) (FUNCTION 03) .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For TCM replacement, see ELECTRICAL AND ELECTRONIC COMPONENTS, LOCATIONS .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For multifunction switch F125 replacement, see TRANSMISSION RANGE SWITCH .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For the replacement of transmission fluid temperature sensor -G93-, see TRANSMISSION FLUID TEMPERATURE SENSOR .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For ATF level checking, see CHECKING FLUID LEVEL .
- For the replacement of transmission fluid temperature sensor -G93-, see TRANSMISSION FLUID TEMPERATURE SENSOR .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For ATF level checking, see CHECKING FLUID LEVEL .
- For the replacement of transmission fluid temperature sensor -G93-, see TRANSMISSION FLUID TEMPERATURE SENSOR .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For ATF level checking, see CHECKING FLUID LEVEL .
- For the replacement of transmission fluid temperature sensor -G93-, see TRANSMISSION FLUID TEMPERATURE SENSOR .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For removal of -G182-, see TRANSMISSION RPM SENSOR .
- For ATF level checking, see CHECKING FLUID LEVEL .
- For DTM, see OUTPUT DIAGNOSTIC TEST MODE (DTM) (FUNCTION 03) .
- To replace solenoid valves and/or valve body, see VALVE BODY .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For ATF level checking, see CHECKING FLUID LEVEL .
- For ATF level checking, see CHECKING FLUID LEVEL .
- For DTM, see OUTPUT DIAGNOSTIC TEST MODE (DTM) (FUNCTION 03) .
- For TCM identification, see ON BOARD DIAGNOSTIC (OBD), CHECKING .
- For DTM, see OUTPUT DIAGNOSTIC TEST MODE (DTM) (FUNCTION 03) .
- For transmission shift element diagrams and tables, see TRANSMISSION SHIFT ELEMENTS .
- For DTM, see OUTPUT DIAGNOSTIC TEST MODE (DTM) (FUNCTION 03) .
- For transmission shift element diagrams and tables, see TRANSMISSION SHIFT ELEMENTS .
- For torque converter removal, see TRANSAXLE .
- For ATF level checking, see CHECKING FLUID LEVEL .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- To replace solenoid valves and/or valve body, see VALVE BODY .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For DTM, see OUTPUT DIAGNOSTIC TEST MODE (DTM) (FUNCTION 03) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For DTM, see OUTPUT DIAGNOSTIC TEST MODE (DTM) (FUNCTION 03) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For DTM, see OUTPUT DIAGNOSTIC TEST MODE (DTM) (FUNCTION 03) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For DTM, see OUTPUT DIAGNOSTIC TEST MODE (DTM) (FUNCTION 03) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For DTM, see OUTPUT DIAGNOSTIC TEST MODE (DTM) (FUNCTION 03) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For DTM, see OUTPUT DIAGNOSTIC TEST MODE (DTM) (FUNCTION 03) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- To replace solenoid valves and/or valve body, see VALVE BODY .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For TCM replacement, see ELECTRICAL AND ELECTRONIC COMPONENTS, LOCATIONS .
- For TCM replacement, see ELECTRICAL AND ELECTRONIC COMPONENTS, LOCATIONS .
- For TCM identification, see ON BOARD DIAGNOSTIC (OBD), CHECKING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For more information regarding Backup Mode, see TCM BACKUP FUNCTIONS .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For more information regarding Backup Mode, see TCM BACKUP FUNCTIONS .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For TCM replacement, see ELECTRICAL AND ELECTRONIC COMPONENTS, LOCATIONS .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For electrical testing, see ELECTRICAL TESTING .
- For electrical testing, see ELECTRICAL TESTING .
- For TCM coding, see CODE CONTROL MODULE (SCAN TOOL FUNCTION 07) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For TCM identification, see ON BOARD DIAGNOSTIC (OBD), CHECKING .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For TCM identification, see ON BOARD DIAGNOSTIC (OBD), CHECKING .
- For ABS diagnosis, see ON BOARD DIAGNOSTIC (OBD) .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For TCM identification, see ON BOARD DIAGNOSTIC (OBD), CHECKING .
- For electrical testing, see ELECTRICAL TESTING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For TCM identification, see ON BOARD DIAGNOSTIC (OBD), CHECKING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For TCM identification, see ON BOARD DIAGNOSTIC (OBD), CHECKING .
- For "Read Measuring Value Block", see READ MEASURING VALUE BLOCK (FUNCTION 08) .
- For TCM identification, see ON BOARD DIAGNOSTIC (OBD), CHECKING .
NOTE:
- Item 11 in Fig 44 : the ignition angle is briefly retarded through this TCM signal, depending on speed and engine RPM, during a transmission range change (shift), in order to soften the shift.
- Item 12 in Fig 44 : if, while there is a driving malfunction or operating malfunction, a transmission range is engaged by hand with the vehicle parked and the engine at high RPM, the ECM will reduce engine torque instantaneously by shielding the injection signals.